DCR-IP5, DCR-IP5E, DCR-IP7BT, DCR-IP7E (serv.man2) - Sony Movie Service Manual (repair manual). Page 2

— 2 —

0

0

0

1.

Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.

2.

Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.

3.

Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.

4.

Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.

5.

Check the B+ voltage to see it is at the values specified.

6.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

Maximum output voltage
DC 8.4 V
Output voltage
DC 7.2 V
Capacity
4.8 Wh (675 mAh)
Operating temperature
0

°

C to 40

°

C (32

°

F to 104

°

F)

Dimensions (approx.)
40.8 

×

 12.5 

×

 49.1 mm

(1 5/8 

×

 1/2 

×

 1 15/16 in.)

(w/h/d)
Mass (approx.)
45 g (1.6 oz)
Type
Lithium ion

Memory
Flash memory
8 MB: MSA-8A
Operating voltage
2.7-3.6 V
Power consumption
Approx. 45 mA in the operating
mode
Approx. 130 

µ

A in the standby

mode
Dimensions (approx.)
50 

×

 2.8 

×

 21.5 mm

(2 

×

 1/8 

×

 7/8 in.) (w/h/d)

Mass (approx.)
4 g (0.14 oz)

Design and specifications are
subject to change without notice.

Generic Access Profile
Dial-up Networking Profile
Usable frequency band
2.4 GHz band
(2.400 – 2.4835 GHz)

1) The maximum rate defined by

Bluetooth specification Ver. 1.1

2) Depends on obstacles between

the Bluetooth devices, radio wave
conditions, etc.

3) Defined by Bluetooth

specification for intended use
between the Bluetooth devices

Power requirements
7.2 V (battery pack)
8.4 V (AC power adaptor)
Average power consumption
(when using the battery pack)
During camera recording using the
viewfinder (brightness normal)
3.5 W
During camera recording using the
LCD (Backlighting on) 4.2 W
During camera recording using the
LCD (Backlighting off) 3.5 W
Operating temperature
0

°

C to 40

°

C (32

°

F to 104

°

F)

Storage temperature
–20

°

C to +60

°

C (–4

°

F to +140

°

F)

Dimensions (approx.)
47

×

 103 

×

 80 mm

(1 7/8 

×

 4 

×

 3 1/8 in.) (w/h/d)

(excluding protruding parts)
Mass (approx.)
310 g (10 oz)
Main unit only
370 g (13 oz)
including the battery pack,
NP-FF50, cassette MGR60, lens cap,
and list strap
Supplied accessories
See page 3.

Power requirements
100 - 240 V AC, 50/60 Hz
Power consumption
23 W
Output voltage
DC OUT: 8.4 V, 1.5 A in the
operating mode
Operating temperature
0

°

C to 40

°

C (32

°

F to 104

°

F)

Storage temperature
–20

°

C to +60

°

C (–4

°

F to +140

°

F)

Dimensions (approx.)
125 

×

 39 

×

 62 mm

(5 

×

 1 9/16 

×

2 1/2 in.) (w/h/d)

excluding (projecting parts) mains
lead
Mass (approx.)
280 g (9.8 oz)
excluding the mains lead