Read Sony DCR-DVD105 / DCR-DVD105E / DCR-DVD605 / DCR-DVD605E (serv.man2) Service Manual online
1-3
DCR-DVD105/DVD105E/DVD605/DVD605E_L2
1-5-3. Self-diagnosis Code Table
C
C
C
C
C
E
E
E
E
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
2
1
3
2
2
0
3
1
4
0
4
0
6
1
6
1
6
1
6
2
6
2
9
4
9
4
Detailed
Code
0
0
0
0
0
2
0
0
5
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
0
0
1
0
0
0
1
Symptom/State
Non-standard battery is used.
Faulty disc is used.
Disc access error
Condensation.
Codec IC dose not return are reply
EEPROM data are rewritten.
Drive fault
Codec IC fault
Audio Codec IC fault
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
Fault of writing to or erasing the flash
memory
memory
Fault of writing to or erasing EEPROM
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Use a compatible disc with the camcorder.
Clean the disc with the supplied cleaning cloth.
Use a compatible disc with the camcorder.
Use a compatible disc with the camcorder.
Remove the disc, and insert it again after one hour.
Remove the power source. Reconnect it again and operate your
camcorder again
camcorder again
Make EEPROM data correct value. (Note)
Inspect or replacement of the mechanism deck, IC (IC4302 on
the VC-421 board) and drive block
the VC-421 board) and drive block
Inspect or replacement of the codec IC (IC3001on the VC-421
board) peripheral circuits
board) peripheral circuits
Inspect or replacement of the Audio Codec IC (IC3001 on the
VC-421 board) peripheral circuits
VC-421 board) peripheral circuits
Inspect the lens block focus reset sensor (pin ql of CN1301 on
the VC-421 board) when focusing is performed when the touch
panel is operated in the focus manual mode and the focus motor
drive circuit (IC1301on the VC-421 board) when the focusing is
not performed.
the VC-421 board) when focusing is performed when the touch
panel is operated in the focus manual mode and the focus motor
drive circuit (IC1301on the VC-421 board) when the focusing is
not performed.
Inspect the lens block zoom reset sensor (pin qg of CN1301 on
the VC-421 board) when zooming is performed when the zoom
switch is operated and the zoom motor drive circuit (IC1301on
the VC-421 board) when zooming is not performed.
the VC-421 board) when zooming is performed when the zoom
switch is operated and the zoom motor drive circuit (IC1301on
the VC-421 board) when zooming is not performed.
Check whether the flexible board of the lens is broken, and
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC1301 on the VC-421 board).
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC1301 on the VC-421 board).
Inspect PITCH angular velocity sensors (SE6302 on the MA-440
board) peripheral circuits.
board) peripheral circuits.
Inspect YAW angular velocity sensors (SE6301 on the MA-440
board) peripheral circuits.
board) peripheral circuits.
Inspect the flash memory (IC3101 on the VC-421 board). (Note)
Inspect the EEPROM (IC2602 on the VC-421 board). (Note)
Note:
Refer to “7-2. Record of Self-diagnosis check” of “3-5. SERVICE MODE”, ADJ (9-876-924-51).
Click on the first or last page to see other DCR-DVD105 / DCR-DVD105E / DCR-DVD605 / DCR-DVD605E (serv.man2) service manuals if exist.