Read Sony CCD-TRV107 / CCD-TRV108 / CCD-TRV308 / CCD-TRV408 / CCD-TRV608 (serv.man3) Service Manual online
CCD-TRV107/TRV108/TRV308/TRV408/TRV608
— 10 —
Sony EMCS Co.
2002G1600-1
©2002.7
Published by DI Customer Center
9-929-926-92
:
Changed portion.
Page
CORRECT
5-31
3-1-3.
Adjusting Connectors
Some of the adjusting points of the video section are concentrated
in CN713 of VC-272 board. Connect the Measuring instrument and
the adjustment remote commander via the I/F unit for LANC control
(J-6082-521-A) and CPC jig connector (J-6082-539-A) to CN713.
To operate the adjustment remote commander, connect the AC power
adapter to the DC IN jack of I/F unit for LANC control, or connect
the L series Info-LITHIUM battery to the battery terminal of I/F
unit for LANC control.
The following table shows the Pin No. and signal name of CN713.
in CN713 of VC-272 board. Connect the Measuring instrument and
the adjustment remote commander via the I/F unit for LANC control
(J-6082-521-A) and CPC jig connector (J-6082-539-A) to CN713.
To operate the adjustment remote commander, connect the AC power
adapter to the DC IN jack of I/F unit for LANC control, or connect
the L series Info-LITHIUM battery to the battery terminal of I/F
unit for LANC control.
The following table shows the Pin No. and signal name of CN713.
Table 5-3-1.
The following table shows the arrangement of the test points of I/F
unit for LANC control. (Pin No. are those of CN713.)
unit for LANC control. (Pin No. are those of CN713.)
Table 5-3-2.
Pin No.
1
2
3
4
5
6
7
8
Signal Name
N.C.
IR VIDEO
BPF MONI
CAP FG
RF SWP
REG GND
REC RF
REG GND
Pin No.
9
10
11
12
13
14
15
16
Signal Name
PB RF
REG GND
LANC OUT
LANC IN
XLANC POWER ON
EVF VG
VCO
N.C.
Pin No.
14
9
3
5
4
Signal Name
BL
EVF VG
PB RF (MON)
BPF MONI
TMS
TDI
SWP
CAP FG
Pin No.
15
6,8,10
7
2
Signal Name
EVF VCO
BL 4.75
GND
REC RF (RF IN)
TDO
TCK
IR VIDEO
Fig. 5-3-1.
CPC jig connector
CPC jig
Remove the CPC lid
CN713
Conductor side
16
1
:
Changed portion.
Page
CORRECT
5-40
5-4. SERVICE MODE
4-1.
ADJUSTMENT REMOTE COMMANDER
1. Using the Adjustment Remote Commander
1)
Connect the adjustment remote commander to CN713 of VC-
272 board via I/F unit for LANC control (J-6082-521-A) and
CPC jig connector (J-6082-539-A). To operate the adjustment
remote commander, connect the AC power adapter (8.4Vdc)
to the DC IN jack of I/F unit for LANC control, or connect the
L series Info-LITHIUM battery to the battery terminal of I/F
unit for LANC control.
272 board via I/F unit for LANC control (J-6082-521-A) and
CPC jig connector (J-6082-539-A). To operate the adjustment
remote commander, connect the AC power adapter (8.4Vdc)
to the DC IN jack of I/F unit for LANC control, or connect the
L series Info-LITHIUM battery to the battery terminal of I/F
unit for LANC control.
