CCD-TR311, CCD-TR311E, CCD-TR411E, CCD-TR412E, CCD-TR511E, CCD-TR512E, CCD-TR640E, CCD-TR730E, CCD-TR840E, CCD-TR845E - Sony Movie Service Manual (repair manual). Page 2

Audio input
(CCD-TR840E : AUS only)/output

CCD-TR311/TR311E/TR411E/
TR412E/TR511E/TR512E/TR640E :
Monaural, Phone jack, 327 mV
CCD-TR730E/TR840E/TR845E :
Phono jacks (2: stereo L and R)
327 mV, (at output impedance 47
kilohms) impedance less than 2.2
kilohms

RFU DC OUT

Special minijack, DC 5V

Headphone jack(CCD-TR730E/
TR840E/TR845E only)

Stereo minijack (ø 3.5 mm)

LANC control jack

Stereo mini-minijack (ø 2.5 mm)

MIC jack

Minijack, 0.388mV low impedance with
2.5 to 3.0 V DC, output impedance 6.8
kilohms (ø 3.5 mm)
CCD-TR311/TR311E/TR411E/
TR412E/TR511E/TR512E/TR640E :
Monaural type
CCD-TR730E/TR840E/TR845E :
Stereo type

Intelligent accessory shoe
(CCD-TR730E/TR840E/TR845E only)

8-pin connector

General
Power requirements

7.2 V (battery pack)
8.4 V (AC power adaptor)

Take a copy CAMERA COLOR REPRODUCTION FRAME
and Parts reference sheets with a clear sheet for use.

CCD-TR311

CCD-TR311E/TR411E/TR412E/TR511E/TR512E/

TR640E/TR730E/TR840E/TR845E

– 2 –

!

!

1. Check the area of your repair for unsoldered or poorly-soldered

connections. Check the entire board surface for solder splashes
and bridges.

2. Check the interboard wiring to ensure that no wires are “pinched”

or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors,

that were installed during a previous repair. Point them out to
the customer and recommend their replacement.

4. Look for parts which, though functioning, show obvious signs

of deterioration. Point them out to the customer and recommend
their replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit board Repairing

• Keep the temperature of the soldering iron around 270

°

C during

repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:

During camera recording
CCD-TR311E/TR311E/TR411E/
TR412E/TR511E/TR512E : 2.5 W
CCD-TR640E : 2.6 W
CCD-TR730E/TR840E/TR845E : 2.7 W

Operating temperature

32

°

F to 104

°

F(0

°

C to 40

°

C)

Storage temperature

-4

°

F to +140

°

F(-20

°

C to +60

°

C)

Dimensions (Approx.)

CCD-TR512E/TR370E :
4 1/4 x 4 1/4 x 7 5/8 in.
(107 x 107 x 193 mm)(w/h/d)
CCD-TR311/TR311E/TR411E/
TR412E/TR511E/TR640E/TR840E/
TR845E :
4 1/4 x 4 1/4 x 8 1/4 in.
(107 x 107 x 209 mm)(w/h/d)

Mass (Approx.)

CCD-TR311/TR311E/TR411E/
TR412E/TR511E (EE, NE, RU, E, HK,
AUS, CN) : 1 lb 11 oz (790 g)
CCD-TR511E (AEP, UK)/TR512E/
TR640E/TR730E/TR840E/TR845E : 1
lb 12 oz (800 g)
excluding the battery pack, lithium
battery, cassette and shoulder strap
CCD-TR311/TR311E/TR411E/
TR412E/TR511E (EE, NE, RU, E, HK,
AUS, CN) : 2 lb (930 g)
CCD-TR511E (AEP, UK)/TR512E/
TR640E/TR730E/TR840E/TR845E : 2
lb 1 oz (940 g)
including the battery pack NP-F330,
lithium battery CR2025, cassette and
shoulder strap

Microphone

CCD-TR311/TR311E/TR411E/
TR412E/TR511E/TR512E/TR640E :
Monaural type
CCD-TR730E/TR840E/TR845E :
Stereo type

Supplied accessories

See page 4.

Power requirements

100 -240 V AC, 50/60 Hz

Power consumption

23 W

Output voltage

DC OUT: 8.4 V, 1.5 A in operating mode

Operating temperature

32

°

F to 104

°

F(0

°

C to 40

°

C)

Storage temperature

-4

°

F to +140

°

F(-20

°

C to +60

°

C)

Dimensions (Approx.)

5 x 1 9/16 x 2 1/2 in. (125 x 39 x 62
mm)(w/h/d) excluding projecting parts

Mass (Approx.)

9.8 oz (280 g) excluding power cord

Design and specifications are subject to
change without notice.