Read Sony CPD-L181 Service Manual online
CPD-L181
– 2 –
Failure
Power LED
Aging
Blink Amber (On 0.5 sec, Off 0.5 sec) .... Blink Green (On 0.5 sec, Off 0.5 sec)
Out of Scan Range
On Green
*Aging mode ........................................... Press MENU key for longer than 5 second.
DIAGNOSIS
TIMING SPECIFICATION
PRIMARY MODE
MODE AT PRODUCTION
MODE 0
MODE 1
MODE 2
MODE 3
MODE 4
MODE 5
MODE 6
MODE 7
RESOLUTION
640 X 480
640 X 480
640 X 480
640 X 480
720 X 400
720 X 400
—
720 X 480
CLOCK
25.175 MHZ
30.240 MHZ
31.500 MHZ
36.000 MHZ
28.350 MHZ
35.500 MHZ
—
31.505 MHZ
— HORIZONTAL —
H-FREQ
31.469 kHz
35.000 kHz
37.500 kHz
43.269 kHz
31.500 kHz
37.927
—
35.162 kHz
usec
usec
usec
usec
usec
usec
usec
usec
H. TOTAL
31.778
28.571
26.667
23.111
31.746
26.366
—
28.440
H. BLK
6.356
7.407
6.349
5.333
6.349
6.085
—
5.586
H. FP
0.636
2.116
0.508
1.556
0.635
1.014
—
1.079
H. SYNC
3.813
2.116
2.032
1.556
3.810
2.028
—
1.270
H. BP
1.907
3.175
3.810
2.222
1.905
3.042
—
3.238
H. ACTIV
25.422
21.164
20.317
17.778
25.397
20.282
—
22.854
— VERTICAL —
V. FREQ(HZ)
59.940 Hz
66.667 Hz
75.000 Hz
85.008 Hz
70.156 Hz
85.039
—
59.901 Hz
lines
lines
lines
lines
lines
lines
lines
lines
V. TOTAL
525
525
500
509
449
446
—
587
V. BLK
45
45
20
29
49
46
—
107
V. FP
10
3
1
1
12
1
—
12
V. SYNC
2
3
3
3
3
3
—
2
V. BP
33
39
16
25
34
42
—
93
V. ACTIV
480
480
480
480
400
400
—
480
— SYNC —
INT(G)
NO
NO
NO
NO
NO
NO
—
NO
EXT(H/V)/POLARITY
YES N/N
YES N/N
YES N/N
YES N/N
YES N/P
YES N/P
—
YES N/N
EXT(CS)/POLARITY
NO
NO
NO
NO
NO
NO
—
NO
INT/NON INT
NON INT
NON INT
NON INT
NON INT
NON INT
NON INT
—
NON INT
Power Saving Function
This monitor meets the power-saving guidelines set by
VESA and
VESA and
E
NERGY
S
TAR, as well as the more stringent
NUTEK .
If the monitor is connected to a computer or video graphics
board that is VESA DPMS (Display Power Management
Signaling) compliant, the monitor will automatically reduce
power consumption in three stages as shown below.
You can set the delay time before the monitor enters the
power saving mode using the OSD. Set the time according
to “Setting the Power Saving Delay Time” on page 1-6.
If the monitor is connected to a computer or video graphics
board that is VESA DPMS (Display Power Management
Signaling) compliant, the monitor will automatically reduce
power consumption in three stages as shown below.
You can set the delay time before the monitor enters the
power saving mode using the OSD. Set the time according
to “Setting the Power Saving Delay Time” on page 1-6.
*
“Sleep” and “deep sleep” are power saving modes defined by
the Environmental Protection Agency.
the Environmental Protection Agency.
** When your computer enters the power saving mode, the input
signal is cut and NO INPUT SIGNAL appears on the screen.
After the time set in “Changing the Power Saving Delay Time”
(page 1-6) has elapsed, the monitor enters the power saving
mode.
After the time set in “Changing the Power Saving Delay Time”
(page 1-6) has elapsed, the monitor enters the power saving
mode.
Power consumption
mode
mode
Normal operation
Standby (1st mode)
Suspend (2nd mode)
(sleep)*
(sleep)*
Active-off (3rd mode)**
(deep sleep)*
(deep sleep)*
Power-off
Main power-off
Power
consumption
consumption
≤
48 W
≤
15 W
≤
15 W
≤
1 W
≤
1 W
0 W
u
Indicator
Green
Green and orange
alternate
alternate
Green and orange
alternate
alternate
Orange
Off
Off
1
2
3
4
5
6
Click on the first or last page to see other CPD-L181 service manuals if exist.