Read Sony DVP-S90D Service Manual online
19
DVP-S90D
Disc Type
1. Disc Type Auto Check
2. DVD SL
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. LCD
12 cm
6. DVD SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. LCD
8 cm
0. Reset SLED TILT
SA. SI. EMG. 00
DVD SL 12 cm
Display when DVD SL 12cm disc was selected
Disc Type
1. Disc Type Auto Check
2. DVD SL
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. LCD
12 cm
6. DVD SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. LCD
8 cm
0. Reset SLED TILT
TC. : : EMG. 00
CD 12 cm
Display when CD 12cm disc was selected
[0]
Reset SLED TILT
Reset the Sled and Tilt to initial posi-
tion.
tion.
[1]
Disk Type Check
Judge automatically the loaded disc. As
the judged result is displayed at the bot-
tom of screen, make sure that it is cor-
rect.
If Disc Check Memory menu has not
been executed after EEPROM default
setting, the disc type cannot be judged.
In this case, return to the initial menu
and make a check for three types of
discs (SL, DL, CD).
the judged result is displayed at the bot-
tom of screen, make sure that it is cor-
rect.
If Disc Check Memory menu has not
been executed after EEPROM default
setting, the disc type cannot be judged.
In this case, return to the initial menu
and make a check for three types of
discs (SL, DL, CD).
[2]
to
[9]
Select the loaded disc. The adjusted
value is written to the address of se-
lected disc. No further entry is neces-
sary if
value is written to the address of se-
lected disc. No further entry is neces-
sary if
[1]
was selected.
[10/0]
Reset SLED TILT
Reset the Sled
and Tilt to initial position.
[1]
LD
Turn ON/OFF the laser.
[2]
SP
Turn ON/OFF the spindle.
[3]
Focus
Search the focus and turn on the focus.
[4]
TRK
Turn ON/OFF the tracking servo.
[5]
Sled
Turn ON/OFF the sled servo.
[6]
CLVA
Turn ON/OFF normal servo of spindle
servo.
servo.
[7]
FCS. Srch
Apply same voltage as that of focus
search to the focus drive to check the
focus drive system.
search to the focus drive to check the
focus drive system.
→ Sled FWD
Move the sled outward. Perform this
operation with the tracking servo turned
off.
operation with the tracking servo turned
off.
← Sled REV
Move the sled inward. Perform this op-
eration with the tracking servo turned
off.
eration with the tracking servo turned
off.
↑ Tilt UP
Move the tilt upward.
↓ Tilt DOWN
Move the tilt downward.
The following menus are normally not used.
3.
Track/Layer Jump
4.
Manual Adjustment
5.
Auto Adjustment
The persons who do not know well about these menus should not
use them.
use them.
2. Servo Control
Servo Control
1. LD
Off R.Sled FWD
2. SP
Off L.Sled REV
3. Focus
Off
4. TRK.
Off
5. Sled
Off
6. CLVA
Off
7. FCS. Srch Off
0. Reset SLED TILT
SA. SI. EMG. 00
DVD SL 12 cm
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
Click on the first or last page to see other DVP-S90D service manuals if exist.