Read Sony DVP-NS585P / DVP-NS590P (serv.man2) Service Manual online
1-4
17
Hookups
Note
When connecting to a progressive TV, it is recommended that you use only pattern A. If you connect to your
TV using both A and B, a special control signal transmitted via the SCART (EURO AV) cable may cause
the signal to be switched to the SCART (EURO AV) jack.
TV using both A and B, a special control signal transmitted via the SCART (EURO AV) cable may cause
the signal to be switched to the SCART (EURO AV) jack.
A
If you are connecting to a monitor, projector, or AV amplifier (receiver)
having component video input jacks (Y, P
B
/C
B
, P
R
/C
R
) (DVP-NS585P only)
Connect the component via the COMPONENT VIDEO OUT jacks using a component video
cord (not supplied) or three video cords (not supplied) of the same kind and length. You will
enjoy accurate colour reproduction and high quality images.
If your TV accepts progressive 525p/625p format signals, use this connection and set the
NORMAL/PROGRESSIVE switch on the rear panel to PROGRESSIVE to accept progressive
video signals. The PROGRESSIVE indicator lights up when the player outputs progressive
signals.
cord (not supplied) or three video cords (not supplied) of the same kind and length. You will
enjoy accurate colour reproduction and high quality images.
If your TV accepts progressive 525p/625p format signals, use this connection and set the
NORMAL/PROGRESSIVE switch on the rear panel to PROGRESSIVE to accept progressive
video signals. The PROGRESSIVE indicator lights up when the player outputs progressive
signals.
B
If you are connecting to a SCART (EURO AV) input jack
Connect the SCART (EURO AV) cord (not supplied). Be sure to make the connections firmly
to avoid hum and noise. When you connect using the SCART (EURO AV) cord, check that the
TV conforms to S video or RGB signals. Refer to the operating instructions supplied with the
TV to be connected. Also, when you set “LINE” to “S VIDEO” or “RGB” under “SCREEN
SETUP” in the Setup Display (page 64), use a SCART (EURO AV) cord that conforms to each
signal.
to avoid hum and noise. When you connect using the SCART (EURO AV) cord, check that the
TV conforms to S video or RGB signals. Refer to the operating instructions supplied with the
TV to be connected. Also, when you set “LINE” to “S VIDEO” or “RGB” under “SCREEN
SETUP” in the Setup Display (page 64), use a SCART (EURO AV) cord that conforms to each
signal.
C
If you are connecting to a video input jack
Connect the yellow plug of the audio/video cord (supplied) to the yellow (video) jacks. You will
enjoy standard quality images.
enjoy standard quality images.
Use the red and white plugs to connect to the audio input jacks (page 20).
D
If you are connecting to an S VIDEO input jack (DVP-NS585P only)
Connect an S VIDEO cord (not supplied). You will enjoy high quality images.
Green
Blue
Red
Green
Blue
Red
Yellow
White (L)
Red (R)
Yellow
White (L)
Red (R)
,continued
18
When connecting to a wide screen TV
Depending on the disc, the image may not fit your TV screen. If you want to change the aspect
ratio, please refer to page 64.
ratio, please refer to page 64.
Notes
• Do not connect a VCR, etc. between your TV and the player. If you pass the player signals via the VCR,
you may not receive a clear image on the TV screen. If your TV has only one audio/video input jack,
connect the player to this jack.
connect the player to this jack.
• Consumers should note that not all high definition television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In case of 525 or 625 progressive scan picture problems,
it is recommended that the user switch the connection to the ‘standard definition’ output. If there are
questions regarding our TV set compatibility with this model 525p and 625p DVD player, please contact
our customer service center.
it is recommended that the user switch the connection to the ‘standard definition’ output. If there are
questions regarding our TV set compatibility with this model 525p and 625p DVD player, please contact
our customer service center.
• When you connect the player to your TV via the SCART (EURO AV) jacks, the TV’s input source is set
to the player automatically when you start playback. In this case, press t (TV/video) on the remote to
return the input to the TV.
return the input to the TV.
• If you set “LINE” to “RGB” in SCREEN SETUP (page 25, 64), the player outputs no component video
signals.
VCR
CD/DVD player
TV
Connect
directly
directly
19
Hookups
Step 4: Connecting the Audio Cords
Refer to the chart below to select the connection that best suits your system. Be sure to also read
the instructions for the components you wish to connect.
the instructions for the components you wish to connect.
Select a connection
Select one of the following connections,
through
.
z
Hint
If you connect an AV amplifier (receiver) that
conforms to the 96 kHz sampling frequency, use
connection .
conforms to the 96 kHz sampling frequency, use
connection .
* Manufactured under license from Dolby
Laboratories. “Dolby,” “Pro Logic,” and the
double-D symbol are trademarks of Dolby
Laboratories.
double-D symbol are trademarks of Dolby
Laboratories.
** “DTS” and “DTS Digital Out” are trademarks
of Digital Theater Systems, Inc.
Components to be connected
Connection
Your setup (example)
TV
(page 20)
Stereo amplifier (receiver) and two speakers
or
MD deck/DAT deck
or
MD deck/DAT deck
(page 21)
AV amplifier (receiver) having a Dolby*
Surround (Pro Logic) decoder and 3 to 6
speakers
Surround (Pro Logic) decoder and 3 to 6
speakers
(page 22)
AV amplifier (receiver) with digital input jacks
having a Dolby Digital, DTS**, or MPEG audio
decoder and 6 speakers
having a Dolby Digital, DTS**, or MPEG audio
decoder and 6 speakers
(page 23)
A
D
A
B
C
D
D
,continued
20
Connecting to your TV
This connection will use your TV’s speakers for sound. If you use the SCART (EURO AV) cord
in pattern B of “Step 3: Connecting the Video Cords” (page 16), you do not have to connect
audio cords to your TV.
in pattern B of “Step 3: Connecting the Video Cords” (page 16), you do not have to connect
audio cords to your TV.
* The yellow plug is used for video signals (page
16).
z
Hint
When connecting to a monaural TV, use a stereo-
mono conversion cord (not supplied). Connect the
LINE OUT L/R (AUDIO) jacks to the TV’s audio
input jack.
mono conversion cord (not supplied). Connect the
LINE OUT L/R (AUDIO) jacks to the TV’s audio
input jack.
A
COMPONENT
VIDEO
OUT
PCM/
DTS/
MPEG/
DOLBY
DIGITAL OPTICAL
DTS/
MPEG/
DOLBY
DIGITAL OPTICAL
COAXIAL
/
PR
/
CR
VIDEO
NORMAL
PROGRESSIVE
PROGRESSIVE
DIGITAL OUT
S VIDEO OUT
LINE OUT
Y
PB
CB
LINE
(RGB)
-TV
L
C E N T E R
A
LINE OUT
AUDIO
R
L
LINE OUT
AUDIO
R
L
TV
l : Signal flow
CD/DVD player
(white)
(red)
Audio/video
cord (supplied)
cord (supplied)
to audio input
(yellow)*
(white)
(red)
(yellow)*
to LINE OUT
L/R (AUDIO)
L/R (AUDIO)
Click on the first or last page to see other DVP-NS585P / DVP-NS590P (serv.man2) service manuals if exist.