DVP-NS305, DVP-NS310, DVP-NS315, DVP-NS405, DVP-NS410, DVP-NS415, HT-1700D - Sony DVD Service Manual (repair manual). Page 69

6-4

(6-2) 1935 RAM

Data write 

t read, and accord check

Error 14: AVD RAM read data discord
The program code data stored in ROM (IC107) are copied
to all areas of RAM (IC504, IC505) connected to the AVD
through the bus, then they are read and checked if they ac-
cord. Further, the same test is conducted once again with
the data where all bits are inverted between 1 and 0. If dis-
cord is detected, faulty address, written data, and read data
are displayed following the error code 14, and the test is
suspended.
During the test, OSD display becomes blank as the OSD
area is also checked.

(6-3) 1935 SP

ROM 

t AVD RAM t Video OUT

Error: Not detected.
The data including sub picture streams in ROM are trans-
ferred to the RAM in AVD, and output as video signals
from the AVD.
Though OSD display becomes blank, the output of video
signals continues until the key is pressed.

(7-2) Color Bar

AVD color bar command write 

t Video OUT

Error: Not detected.
The command is transferred to the AVD, and the color bar
signals are output from video terminals.

(7-3) Composite Out (European model only)

EURO-AV video output check
AVD color bar command write 

t Video (EURO-AV) OUT

Error: Not detected.
With the component of video output turned off, the color
bar signals are output from the EURO-AV terminal.
This check is performed for European model only.

(7-4) Y/C Out (European model only)

Y/C video output check
AVD color bar command write 

t Video (Y/C) OUT

Error: Not detected.
With the Y/C of video output turned on, the color bar sig-
nals are output.
This check is performed for European model only.

(7-5) RGB Out (European model only)

RGB video output check
AVD color bar command write 

t Video (RGB) OUT

Error: Not detected.
With the RGB of video output turned on, the color bar sig-
nals are output.
This check is performed for European model only.

(7-6) Component Out (European model only)

Component video output check
AVD color bar command write 

t Video (Component) OUT

Error: Not detected.
With the component of video output turned on, the color
bar signals are output.
This check is performed for European model only.

(7-7) Euro AV Through (European model only)

AV Through output On/Off
Error: Not detected.
AV Through output is turned on.
This check is performed for European model only.

8. Audio Output
(8-2) ARP 

t1935

Data flow from supply system DRAM to SDRAM of AV
Decoder is tested.
Error 15: ARP 

t 1935 video NG

16: ARP 

t 1935 audio NG

(8-3) Test Tone

Pink noise output
Error: Not detected.
In the models without DD output, the test tone is output
from L and R of 2-channel only, and in the models with
DD output, the test tone is output from L and R of 2-chan-
nel, and all channels of 5.1 output.
After turning on all outputs, each time the [NEXT] key is
pressed, the output channel is switched for individual chan-
nel checking.

2. Version Display
(2-2) Revision
(2-3) ROM Check Sum
(2-4) Model Type
(2-5) Region
(2-6) M’t Check

3. Peripheral
(3-2) EEPROM Check
(3-7) ———— (Function not supported)

4. Servo
(4-2) Servo DSP Check
(4-3) ———— (Function not supported)
(4-4) RF Amp Register Check

5. Data Supply System
(5-2) ARP Register Check
(5-3) ARP to RAM Data Bus
(5-4) ARP to RAM Address Bus
(5-5) ARP RAM Check

6. AV Decoder
(6-2) 1935 RAM
(6-3) 1935 SP

7. Video Output
(7-2) Color Bar
(7-3) Composite Out (European model only)
(7-4) Y/C Out (European model only)
(7-5) RGB Out (European model only)
(7-6) Component Out (European model only)
(7-7) Euro AV Through (European model only)

8. Audio Output
(8-2) ARP 

t1935

(8-3) Test Tone