Read Sony DVP-F35P Service Manual online
1-6
26
6
Press ENTER.
The Setup Display for selecting the
aspect ratio of the TV to be connected
appears.
aspect ratio of the TV to be connected
appears.
7
Press X/x to select the setting that
matches your TV type.
matches your TV type.
◆ If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
• 16:9 (page 68)
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
standard TV with a wide-screen mode
• 16:9 (page 68)
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
(page 68)
8
Press ENTER.
The Setup Display for selecting the type
of jack used to connect your amplifier
(receiver) appears.
of jack used to connect your amplifier
(receiver) appears.
9
Press X/x to select the type of jack
(if any) you are using to connect to
an amplifier (receiver), then press
an amplifier (receiver), then press
ENTER.
Choose the item that matches the audio
connection you selected on pages 21 to
24 (
connection you selected on pages 21 to
24 (
through
).
• If you connect just a TV and nothing
else, select “NO.” Quick Setup is
finished and connections are complete.
finished and connections are complete.
• Select “AUDIO OUTPUT L/R.” Quick
Setup is finished and connections are
complete.
complete.
• Select “DIGITAL OUTPUT.” The
Setup Display for “DOLBY DIGITAL”
appears.
appears.
10
Press X/x to select the type of
Dolby Digital signal you wish to
send to your amplifier (receiver).
Choose the signal that matches the audio
connection you selected on pages 22 to
24 (
connection you selected on pages 22 to
24 (
through ).
• D-PCM (page 72)
• DOLBY DIGITAL (only if the
amplifier (receiver) has a Dolby Digital
decoder) (page 72)
decoder) (page 72)
11
Press ENTER.
“DTS” is selected.
AUTO
SCREEN SETUP
TV TYPE:
16:9
4:3 PAN SCAN
BACKGROUND:
MODE
MODE
(PROGRESSIVE)
:
16:9
SCREEN SAVER:
4:3 LETTER BOX
YES
NO
Is this player connected to an amplifier
(receiver) ? Select the type of jack you
are using.
(receiver) ? Select the type of jack you
are using.
AUDIO OUTPUT L/R
DIGITAL OUTPUT
A
D
A
B-1
C-1
B-2
C-2
D
B
D
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
AUDIO DRC:
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
MPEG:
OFF
STANDARD
ON
DOWNMIX:
DOLBY SURROUND
D-PCM
48kHz/96kHz PCM:
48kHz/16bit
DTS:
DOLBY DIGITAL
D-PCM
B-2
C-2
D
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
AUDIO DRC:
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
MPEG:
OFF
STANDARD
ON
DOWNMIX:
DOLBY SURROUND
D-PCM
PCM
DTS:
OFF
OFF
OFF
ON
48kHz/96kHz PCM:
27
H
ook
up
s
s
12
Press X/x to select whether or
not you wish to send a DTS signal
to your amplifier (receiver).
to your amplifier (receiver).
Choose the item that matches the audio
connection you selected on pages 22 to
24 (
connection you selected on pages 22 to
24 (
through
).
• OFF (page 72)
• ON (only if the amplifier (receiver) has
a DTS decoder) (page 72)
13
Press ENTER.
Quick Setup is finished. All connections
and setup operations are complete.
If your AV amplifier (receiver) has an
MPEG audio decoder, set “MPEG” to
“MPEG” (page 72).
and setup operations are complete.
If your AV amplifier (receiver) has an
MPEG audio decoder, set “MPEG” to
“MPEG” (page 72).
Enjoying the surround sound
effects
effects
To enjoy the surround sound effects of this
player or your amplifier (receiver), set the
following items as described below for the
audio connection you selected on pages 22 to
24 (
player or your amplifier (receiver), set the
following items as described below for the
audio connection you selected on pages 22 to
24 (
through
). Each of these is the
default setting and does not need to be
adjusted when you first connect the player.
See page 66 for using the Setup Display.
adjusted when you first connect the player.
See page 66 for using the Setup Display.
Audio Connection (pages 22 to 24)
• No additional settings are needed.
• Set “DOWNMIX” to “DOLBY
SURROUND” (page 71)
• If the sound distorts even when the volume
is turned down, set “AUDIO ATT” to “ON”
(page 71)
(page 71)
• Set “DOWNMIX” to “DOLBY
SURROUND” (page 71)
• Set “DIGITAL OUT” to “ON” (page 71)
Attaching the Stand
You can use the player laid horizontally, or in
an vertical position. Be sure to attach the
supplied stand when using in the vertical
position.
an vertical position. Be sure to attach the
supplied stand when using in the vertical
position.
1
Fit the projection of the stand into
the
slot on the
side of the player.
2
Slide the stand back and forth to
align the screw holes.
align the screw holes.
Select two screw holes to decide the foot
position.
position.
3
Secure the two supplied screws.
4
Stand the player up.
B
D
B-2
C-2
D
B
D
A
B-1
C-1
B-2
C-2
D
,
continued
28
z Hint
When you want to align the front of the player with
other vertical equipment, you can adjust the foot
position by selecting two screw holes in step 2.
When you want to align the front of the player with
other vertical equipment, you can adjust the foot
position by selecting two screw holes in step 2.
Notes
• Do not attach the stand when using the player laid
horizontally. Also, be sure to attach the stand
when positioning the player vertically as the
player may fall over.
when positioning the player vertically as the
player may fall over.
• When moving the player, hold the player itself. If
you hold the stand, it may break.
• Keep the screws out of reach of children as they
may swallow them.
29
Pl
ay
in
in
g Di
sc
s
Playing Discs
Playing Discs
Depending on the DVD or VIDEO CD, some
operations may be different or restricted.
Refer to the operating instructions supplied
with your disc.
operations may be different or restricted.
Refer to the operating instructions supplied
with your disc.
1
Turn on your TV.
2
Press
[/1.
The player turns on.
3
Switch the input selector on your
TV so that the signal from the
TV so that the signal from the
player appears on the TV screen.
◆ When using an amplifier (receiver)
Turn on the amplifier (receiver) and
select the appropriate channel so that you
can hear sound from the player.
Turn on the amplifier (receiver) and
select the appropriate channel so that you
can hear sound from the player.
4
Slowly, insert the disc straight into
the disc slot.
5
Press
H.
The player starts playback (continuous
play). Adjust the volume on the TV or the
amplifier (receiver).
Depending on the disc, a menu may
appear on the TV screen. For DVD
VIDEOs, see page 32. For VIDEO CDs,
see page 33.
play). Adjust the volume on the TV or the
amplifier (receiver).
Depending on the disc, a menu may
appear on the TV screen. For DVD
VIDEOs, see page 32. For VIDEO CDs,
see page 33.
To turn off the player
Press [/1. The player enters standby mode.
When playing 8 cm discs
You can play an 8 cm disc without the need
for an adapter. An adapter may cause a
malfunction.
for an adapter. An adapter may cause a
malfunction.
z Hint
You can have the player turn off automatically
whenever you leave it in stop mode for more than
30 minutes. To turn this function on or off, set
“AUTO POWER OFF” in “CUSTOM SETUP” to
“ON” or “OFF” (page 70).
You can have the player turn off automatically
whenever you leave it in stop mode for more than
30 minutes. To turn this function on or off, set
“AUTO POWER OFF” in “CUSTOM SETUP” to
“ON” or “OFF” (page 70).
Note
When handling the disc, take care not to touch the
playback side. If the disc becomes dirty, wipe from
the centre out with a soft cloth (page 8).
playback side. If the disc becomes dirty, wipe from
the centre out with a soft cloth (page 8).
[/1
N
[
/
1
H
The labelled side
(non-playback side)
facing up
(non-playback side)
facing up
,
continued
Click on the first or last page to see other DVP-F35P service manuals if exist.