DAV-DZ100, HCD-DZ100 - Sony DVD Service Manual (repair manual). Page 2

2

Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 

°C.

Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

• Keep the temperature of the soldering iron around 270 °C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.

This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.

Outputs

Video: 1 Vp-p 75 ohms
S video:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms

P

B

/C

B

, P

R

/C

R

: 0.7 Vp-p 

75 ohms

Video: 1 Vp-p 75 ohms
R/G/B: 0.7 Vp-p 75 ohms

(EXCEPT AEP, UK, RU)

(AEP, UK, RU)

Antenna (aerial)

AM loop antenna (aerial)

Intermediate frequency

450 kHz

Middle eastern models: 

531 – 1,602 kHz (with the 
interval set at 9 kHz)

Other models: 

530 – 1,710 kHz (with the 
interval set at 10 kHz)
531 – 1,602 kHz (with the 
interval set at 9 kHz)

Power requirements 
North American and Mexican models:

120 V AC, 60 Hz

Central/South American models:

110 – 240 V AC, 50/60 Hz

Taiwan model:

12

Korean model:

220 V AC, 60 Hz

0 V AC, 50/60 Hz

Other models:

220 – 240 V AC, 50/60 Hz

Power consumption

On: 135 W
Standby: 0.3 W (at the 
Power Saving mode) 

Dimensions (approx.)

430   70   295 mm 
(17     2 

7

/

8

  11 

5

/

8

 inches) 

(w/h/d) incl. projecting 
parts

Mass (approx.)

3.6 kg (7 lb 15 oz)

Design and specifications are subject to change 
without notice.

×

×

×

×

AEP, UK models

2-588-951-0

[]

RU model

2-588-951-1

[]

EA model

2-588-951-2

[]

SP model

2-588-951-3

[]

CND model

2-588-951-4

[]

AUS model

2-588-951-5

[]

KR model

2-588-951-6

[]

E32 model

2-588-951-7

[]

MX model

2-588-951-9

[]

US model

2-634-883-1

[]

• Abbreviation

AUS

: Australian model

CND

: Canadian model

E32

: 110-240V AC area
  in E model

EA

: Saudi Arabia model

KR

: Korean model

MX

: Mexican model

RU

: Russian model

SP

: Singapore model

Parts No.