Read Sony SAL70300G (serv.man4) Service Manual online
SERVICE MANUAL
SAL70300G (4.5-5.6/70-300 G SSM) (70-300mm F4.5-5.6 G SSM)
SUPPLEMENT-2
File this supplement with the service manual.
(09-429)
Ver. 1.3 2010.03
Sony EMCS Co.
2010C0800-1
© 2010.03
Published by Tokai TEC
US Model
Canadian Model
AEP Model
Chinese Model
Japanese Model
• Revision of ADJUSTMENTS
• [FOCUS-SHIFT/FRANGE BACK (f’F) CHECK/ADJUSTMENT]
• Change of specification (Focus-shift)
• Addition of [In case the thinkness of adjustment washer is over 1.1 mm.]
• [FOCUS-SHIFT/FRANGE BACK (f’F) CHECK/ADJUSTMENT]
• Change of specification (Focus-shift)
• Addition of [In case the thinkness of adjustment washer is over 1.1 mm.]
9-852-270-82
SAL70300G
(4.5-5.6/70-300 G SSM) (70-300mm F4.5-5.6 G SSM)
・ ADJUSTMENTSの改版
「像点移動量/フランジバック(f’
「像点移動量/フランジバック(f’
F)の確認/調整」
・ 規格値の変更(像点移動量)
・ 「バック調整ワッシャの厚みが1.1mmを超えてしまう場合について」の追加
・ 「バック調整ワッシャの厚みが1.1mmを超えてしまう場合について」の追加
4-5. 像点移動量/フランジバック(f’
F)の
確認/調整
4-5-1. 像点移動量/フランジバック(f’
F)の確認
規格値(Table 4-5-1)を以下の内容に変更します。
焦 点 距 離
焦 点 距 離
焦 点 距 離
焦 点 距 離
焦 点 距 離 f (mm)
f (mm)
f (mm)
f (mm)
f (mm)
7 0
7 0
7 0
7 0
7 0
1 0 0
1 0 0
1 0 0
1 0 0
1 0 0
1 3 5
1 3 5
1 3 5
1 3 5
1 3 5
2 0 0
2 0 0
2 0 0
2 0 0
2 0 0
3 0 0
3 0 0
3 0 0
3 0 0
3 0 0
f'F の許容値 (mm)
44.56 (+0.6/-0.3)
基準 = 44.56mm
(44.26 ∼ 45.16)
4-5-2. 像点移動量/フランジバック(f'F)の調整
4. バック調整ワッシャの厚みが1.1mmを超えてしまう場合
について
注意: 「3. 調整方法2 (WIDE 端)」にてバック調整ワッ
シャの厚みが1 . 1 m m を超えてしまう場合は(プリ
セットレバーが選択できないとき),以下の手順を
実施してください。
セットレバーが選択できないとき),以下の手順を
実施してください。
1) Fig.で図示しているように5群レンズASSYを取り外す。
2) ポリイミドフィルムテープ(7-600-004-62)をFig.に
2) ポリイミドフィルムテープ(7-600-004-62)をFig.に
て指示しているサイズにカットし,5群レンズASSYの指
示箇所に貼り付ける。
示箇所に貼り付ける。
3) レンズを組み立てる。
4) 「4-5-2. 像点移動量/フランジバック(f'F)の調整」
4) 「4-5-2. 像点移動量/フランジバック(f'F)の調整」
を実施する。
4-5. FOCUS-SHIFT/FLANGE BACK (f’F)
CHECK/ADJUSTMENT
4-5-1. Focus-shift/Flange Back (f’F) Check
Specification (Table 4-5-1) is changed to the following table.
Focal-length f (mm)
70
100
135
200
300
Tolerance of f’F (mm)
44.56 ( +0.6/-0.3 )
Basis value: 44.56mm
(44.26 to 45.16)
4-5-2. Focus-shift/Flange Back (f’F) Adjustment
4.
In case the thickness of adjustment washer is over 1.1mm.
Note:
If the thickness of back adjustment washer is over 1.1mm
by “3. Adjustment Procedure 2 (WIDE end)” (When the
preset lever cannot be selected. ), make adjust with following
method.
by “3. Adjustment Procedure 2 (WIDE end)” (When the
preset lever cannot be selected. ), make adjust with following
method.
1)
Remove the 5th lens assy as shown in Fig.
2)
Cut the TAPE, PI FILM (NO.5413) 14X33M (7-600-004-62)
to the size indicated, and affix it to the six positions as shown
in Fig. of 5th lens assy.
to the size indicated, and affix it to the six positions as shown
in Fig. of 5th lens assy.
3)
Assemble the lens unit.
4)
Perform the “4-5-2. Focus-shift/Flange Back (f’F) Adjustment”.
3.8mm
: Attaching portion
PI Film(No.5413)14x33m Tape
5th Lens Assy
:
貼り付け位置
ポリイミドフィルムテープ
5群レンズAssy
1.6mm
Fig.
Display