Read Sony DSC-W620 Service Manual online
DSC-W620
2-4
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
2-1-2. CHASSIS SECTION
ns: not supplied
DISASSEMBLY
51
4-416-436-01
LID (S), BATTERY (SILVER)
51
4-416-437-01
LID (B), BATTERY (BLACK)
51
4-416-438-01
LID (R), BATTERY (RED)
52
4-416-440-01
SPRING, BATTERY LID
53
4-416-439-01
SHAFT, BATTERY LID
54
X-2583-617-1 FRAME
ASSY,
MAIN
55
4-416-460-01
SHEET, LID SHAFT RETAINER
56
4-416-459-01
BLOCK, MYLAR (ST)
57
A-1861-588-A STROBOSCOPE BLOCK ASSY (Note 2)
58
A-1861-586-A MAIN MOUNTED PC BOARD (Note 1)
59
1-490-181-11
SWITCH BLOCK, CONTROL
60
1-853-165-11
BATTERY, LITHIUM SECONDARY
61
1-858-625-21
SPEAKER (1.0CM) (Note 3)
62
1-542-918-11 MICROPHONE
63
X-2583-619-1 LCD SHEET METAL ASSY
64
1-811-402-31 LCD
MODULE
65
A-1861-584-A CCD
BLOCK
ASSY
66
4-416-433-01
RUBBER, LIGHT INTERCEPTION
67
4-416-434-01
FILTER, IR CUT (Note 4)
F1
1-576-363-11 FUSE (1A/30V)
F2
1-576-913-31
MICRO FUSE-LINK (1608 TYPE) (1.6A/36V)
#S3
4-151-758-01
SCREW TP 1.4 L3.5
#S4
3-113-001-01 SCREW
TP
1.4*2.5
1. Remove in numerical order (
1
to
5
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
: Solder
1
Turn Over the LCD (
1
) → #S3 X 3
3
Remove the solderings → #S3 X 3
Back View
#S3
1
Back View
#S3
#S3
Solder position
Solder position
Speaker Harness
Microphone Harness
Solder position
51
52
53
#S4
#S3
F2
F1
ns
ns
#S3
#S3
#S3
54
4
Lens Block Section
(See Page 2-5)
5
57
(Note 2)
3
58
(Note 1)
2
64
1
63
55
60
59
56
61
(Note 3)
62
67
(Note 4)
66
65
(Note
5, 6
)
When removing solder, be careful
not to add heat to the board and
the control switch block.
not to add heat to the board and
the control switch block.
When soldering, be careful for solder not to
flow in the contact portion of battery.
flow in the contact portion of battery.
1
Note
Note 1: Refer to "Assembly-1: Installation Cautions of the Main
Board.".
Note 2: Refer to "Assembly-2: Installation Cautions of the Strobe
Board.".
5
Remove the solderings → #S3 X 3
Top View
#S3
Soldering position
Note 3: Refer to "Assembly-3: Installation Cautions of the Speaker
(1.0cm).".
Note 4: Refer to "Assembly-4: How to distinguish the side of Optical
Filter Block facing to Lens Device".
Caution:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Note 6: Refer to "Assembly-5: Connector Locking Method.".
Note 5: To release the lock of the connector, gradually lift up the Lock plate in an order shown below to avoid damaging the Lock plate.
Lock Plate
Main Board
CCD Block Assy
Flexible Board
Flexible Board
CCD Block Assy
3
1
2
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2013.07
Click on the first or last page to see other DSC-W620 service manuals if exist.