Read Sony DSC-S1900 / DSC-S2000 / DSC-S2100 (serv.man2) Service Manual online
DSC-S1900/S2000/S2100_ADJ
Sony Corporation
Revision History
Ver.
Date
History
Contents
S.M. Rev.
issued
SECTION 5
ADJUSTMENT
ADJ
985275053.pdf
2010D29-1
© 2010.4
Published by Sony Techno Create Corporation
Ver. 1.2 2010.04
—
Replace the previously issued SERVICE MANUAL 9-852-750-51
with this Manual.
• Addition of PREPARATIONS.
S.M. Revised:
Page 5-2, 5-3
• Addition of PRODUCT ID LIST.
S.M. Revised:
Page 5-7
Replace the previously issued SERVICE MANUAL 9-852-750-52
with this Manual.
• Addition of PRODUCT ID LIST.
S.M. Revised:
Page 5-7
Official Release
Revised-1
Revised-1
(A1 09-475)
Revised-2
(A2 10-017)
2010.01
2010.04
2010.04
2010.04
1.0
1.1
1.1
1.2
9-852-750-53
DSC-
S1900
/S2000/S2100
—
Yes
Yes
Link
• PREPARATIONS
• Adjustment Items When Replacing CCD
block, Lens block and Main board
• List of Service Tools and Equipments
• Connecting the Equipments
• Handing of Firmware
• Connecting the Equipments
• Handing of Firmware
• CAMERA SECTION ADJUSTMENTS
• Introduction
• Iris/Mechanical Shutter/Bad Pixel
• Iris/Mechanical Shutter/Bad Pixel
Adjustment
• Zoom Adjustment
• Far Focus Adjustment
• Near Focus Adjustment
• White Balance Adjustment
• Set Language Destination
• Far Focus Adjustment
• Near Focus Adjustment
• White Balance Adjustment
• Set Language Destination
• PRODUCT ID LIST
DSC-S1900/S2000/S2100_ADJ
5-2
5. ADJUSTMENTS
5-1. PREPARATIONS
Note1:
Use the fully charged Nickel-Metal Hydride batteries.
Use the fully charged Nickel-Metal Hydride batteries.
Note2:
For the chart, search “J-6082-563-A” in the JIG & Software on ESI homepage, download the PDF file and print out it on the A4 size whitepaper.
For the chart, search “J-6082-563-A” in the JIG & Software on ESI homepage, download the PDF file and print out it on the A4 size whitepaper.
5-1-3. Connecting the Equipments
Connect the equipments as shown below.
5-1-1. Adjustment Items When Replacing CCD block, Lens block and Main board
When replacing these parts, adjust the items indicated by “z” in the following table.
Adjustment
Replaced parts
CCD block
Lens block
Main board
Iris/Mechanical Shutter/Bad Pixel
Adjustment
Adjustment
z
z
z
Zoom Adjustment
z
z
Far Focus Adjustment
z
z
z
Near Focus Adjustment
z
z
z
White Balance Adjustment
z
z
Set Language Destination
z
5-1-4. Handing of Firmware
Note1:
Save the firmware file in the root directory of Memory Stick PRO Duo.
Saving it in the other directory causes the malfunction of program.
Save the firmware file in the root directory of Memory Stick PRO Duo.
Saving it in the other directory causes the malfunction of program.
Note2:
The firmware file is downloadable from the ESI homepage.
The firmware file is downloadable from the ESI homepage.
Preparations:
First, format the Memory Stick PRO Duo before copying the firmware.
When formatting, perform on the PC, using the FAT. Do not format on the unit.
If the concealed file “MEMSTICK.IND” exists, delete it.
Decompress the file and confirm the file format as shown below.
First, format the Memory Stick PRO Duo before copying the firmware.
When formatting, perform on the PC, using the FAT. Do not format on the unit.
If the concealed file “MEMSTICK.IND” exists, delete it.
Decompress the file and confirm the file format as shown below.
Adjusting firmware file for DSC-S1900: A3521C.bin
Adjusting firmware file for DSC-S2000: SDCA352C.bin
Adjusting firmware file for DSC-S2100: SDCC350C.bin
Save the file in the root directory of Memory Stick PRO Duo.
And also save the file of “lang.txt” in the root directory Memory Stick PRO Duo when replacing Main board.
Refer to [5-2-7. Set Language Destination] for “lang.txt”.
This Memory Stick PRO Duo saved the firmware is used in the adjustments.
And also save the file of “lang.txt” in the root directory Memory Stick PRO Duo when replacing Main board.
Refer to [5-2-7. Set Language Destination] for “lang.txt”.
This Memory Stick PRO Duo saved the firmware is used in the adjustments.
Adjustment mode:
1. With the camera turned OFF, set the Mode switch to “
1. With the camera turned OFF, set the Mode switch to “
(Still image)” and insert the Memory Stick PRO Duo with the firmware files into the
Memory Stick slot of the camera.
2. While pressing the “ (Delete)” button, press the “ON/OFF (Power)” button and release when the ON/OFF (Power) lamp and the LCD display
turns on. Release the “ (Delete)” button when the ON/OFF (Power) lamp and the LCD display goes out.
3. After a few seconds, the LCD display will turn white and then show the Adjustment mode screen.
Pushing “MENU” button, the adjustment is finished makes to return to the initial screen display for adjustments.
To continue the adjustment, preform the operations mentioned from the next page.
When all adjustments are completed, just simply remove the power from the unit completes the adjustment procedure.
5-1-2. List of Service Tools and Equipments
HR 15/51:HR6 (size AA)
Nickel-Metal Hydride batteries
Nickel-Metal Hydride batteries
Note: Use the fully charged Nickel-Metal
Hydride batteries.
Memory Stick PRO Duo
(256 MB or more)
(256 MB or more)
DSC-
S1900
/ S2000 / S2100 Bottom Side
J-5
Small pattern box
PTB-1450
J-6082-557-A
PTB-1450
J-6082-557-A
J-4
Chart
(Note2)
(Note2)
J-6
HR 15/51:HR 6 (size AA)
Nickel-Metal Hydride
batteries (× 2) (Note1)
Nickel-Metal Hydride
batteries (× 2) (Note1)
Camera table
Fig. 5-1-1
J-6082-384-A
J-1
SONY
Memory Stick PRO Duo
(256 MB or more)
Memory Stick PRO Duo
(256 MB or more)
J-2
Mini flange back jig
J-6082-719-A
J-6082-719-A
or
Flange back
adjustment jig
J-6082-563-A
adjustment jig
J-6082-563-A
The changed portions from
Ver.1.0 are shown in blue.
Ver.1.0 are shown in blue.
Ver.1.1 2010.04
DSC-S1900/S2000/S2100_ADJ
5-3
The initial screen for the adjustment mode is as follow. (Fig.5-2-2)
Still image
ON/OFF (Power) button
Shutter button
(Key S1)
(Key S1)
(Delete) button
Control button
Fig. 5-2-1
z button (Key OK)
b button (Key Left)
v button (Key Up)
B button
(Key Right)
(Key Right)
V button (Key Down)
Mode switch
MENU button
Key
OK: WB/ISO Adjust
Key
Down: Zoom Adjust
Key Left: Far Focus Adjust
Key
Key
Right: Near Focus Adjst
Up: MS/BP Adjust
Key
Key
S1: Set Lang Destination
Fig. 5-2-2
5-2. CAMERA SECTION ADJUSTMENTS
5-2-1. Introduction
After CCD block, Lens block or Main board replacement, perform adjustments to operate the camera.
Following are keys and functions used in the adjustments. (Fig.5-2-1)
Following are keys and functions used in the adjustments. (Fig.5-2-1)
Note: Keep the Mode switch on “
(Still image)” position during adjustment.
Ver.1.1 2010.04
The changed portions from
Ver.1.0 are shown in blue.
Ver.1.0 are shown in blue.
DSC-S1900/S2000/S2100_ADJ
5-4
5-2-2. Iris/Mechanical Shutter/Bad Pixel Adjustment
The Iris, Mechanical Shutter and Bad Pixel Adjustment order is as follows.
Small pattern box (PTB-1450) setting:
Color temperature = 3150 ± 50K
Luminance: LV12.3 ± 0.2
Adjustments order
The adjustment is finished abnormally.
O ADJUST IRIS OK
X Still Pixel NG
O Mshutter OK
O PreviewPixel OK
O PreviewPixel OK
Fig. 5-2-8
Malfunction of StillPixel adjust-
ment.
X ADJUST IRIS NG
O Still Pixel OK
O PreviewPixel OK
X Mshutter NG
Fig. 5-2-9
Malfunction of Iris & Mechanical
Shutter adjustment.
X PreviewPixel NG
O Mshutter OK
O Still Pixel OK
X ADJUST IRIS NG
Fig. 5-2-10
Malfunction of Iris & PreviewPixel
adjustment.
X Still Pixel NG
O Mshutter OK
O PreviewPixel OK
O PreviewPixel OK
X ADJUST IRIS NG
Fig. 5-2-11
Malfunction of Iris & StillPixel
adjustment.
X ADJUST IRIS NG
X Mshutter NG
X PreviewPixel NG
X Mshutter NG
X PreviewPixel NG
O Still Pixel OK
Fig. 5-2-12
Malfunction of Iris, Mechanical
Shutter & PreviewPixel adjust-
ment.
X PreviewPixel NG
O Mshutter OK
X ADJUST IRIS NG
X Still Pixel NG
Fig. 5-2-13
Malfunction of Iris, PreviewPixel
& StillPixel adjustment.
X ADJUST IRIS NG
O PreviewPixel OK
X Mshutter NG
X Still Pixel NG
Fig. 5-2-14
Malfunction of Iris, Mechanical
Shutter & StillPixel adjustment.
X Mshutter NG
X Still Pixel NG
O ADJUST IRIS OK
X PreviewPixel NG
Fig. 5-2-15
Malfunction of Mechanical Shut-
ter, PreviewPixel & StillPixel
adjustment.
X ADJUST IRIS NG
X Mshutter NG
X PreviewPixel NG
X Mshutter NG
X PreviewPixel NG
X Still Pixel NG
Fig. 5-2-16
Malfunction of all adjustment.
The adjustment finished normally.
O ADJUST IRIS OK
O Mshutter OK
O Mshutter OK
O Still Pixel OK
O PreviewPixel OK
Fig. 5-2-4
The adjustment is complete.
The adjustment is finished abnormally.
X ADJUST IRIS NG
O Mshutter OK
O Still Pixel OK
O PreviewPixel OK
Fig. 5-2-5
Malfunction of Iris adjustment.
O PreviewPixel OK
O Still Pixel OK
O Still Pixel OK
O ADJUST IRIS OK
X Mshutter NG
O PreviewPixel OK
O Still Pixel OK
O Still Pixel OK
Fig. 5-2-6
Malfunction of mechanical shutter
adjustment.
O ADJUST IRIS OK
X PreviewPixel NG
O Mshutter OK
O Still Pixel OK
Fig. 5-2-7
Malfunction of PreviewPixel
adjustment.
Screen display
Set the unit to the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “PREPARATIONS” (Page 5-2).
Place the camera in front of the Small pattern box (PTB-1450). (Fig. 5-2-3)
Press the control button “ v (Key Up)”, then Iris/Mechanical Shutter/Bad Pixel Adjustment starts.
Confirm the indication
on the screen.
.
y
ll
a
m
r
o
n
b
a
d
e
h
s
i
n
i
F
.
y
ll
a
m
r
o
n
d
e
h
s
i
n
i
F
In case of the adjustment is finished normally.
The adjustment completion indication appears
on the screen. (Fig. 5-2-4)
Turn off the power to quit the adjustment mode.
In case of the adjustment is finished abnormally.
The following indication appears on the screen.
(Fig. 5-2-5 to 5-2-16)
In this case, confirm the adjusting environment
and readjust.
Small pattern box
(PTB-1450)
Equipments required: Small pattern box (PTB-1450)
Camera table
Fig. 5-2-3
0.5
to
1.0 cm
Camera
