Read Sony DSC-RX100M2 (serv.man2) Service Manual online
DSC-RX100M2_L2
2-5
2-1-2. OVERALL SECTION-2
ns : not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
4-417-286-01
LIGHT SHIELD RING
52
A-1948-755-A SY-1021 BOARD, COMPLETE (SERVICE)
53
4-467-792-01
STRAP (R) (710)
54
A-1948-503-A LC-1011 BOARD, COMPLETE
55
Selection Parts SPACER PLATE
56
A-1948-509-A CD-847 FLEXIBLE BOARD, COMPLETE (SERVICE)
(including CP001 (CMOS imager)) (Note 4, 5, 6)
57
4-435-725-01
SHEET (500), FLEXIBLE FIXED
58
A-1887-590-A SE-184 FLEXIBLE BOARD, COMPLETE
59
4-433-867-01
SHEET (500), SE FLEXIBLE FIXED
60
4-433-874-01
SHEET (CD) (500), RADIATION (Note2)
61
4-470-489-01
SHEET (STRAP (R)) (710)
ANT601 A-1955-432-A ANTENNA ASSY (SERVICE), NFC (Note 8)
ANT801 1-754-883-11
ANT801 1-754-883-11
ANTENNA (Note 8)
SP901
1-858-785-11
LOUDSPEAKER (0.8CM) (Note 8)
#177
3-208-537-21
0+Z M1.4X2 NEW TORASUTA
#247
4-412-769-11
SCREW (M1.4), NEW TRU-STAR, P2 (Note 7)
#257
3-208-537-41
0+Z M1.4X2 NEW TORASUTA
#302
3-703-816-18
SCREW (M1.4X3.5), SPECIAL HEAD
1. Remove in numerical order (
1
to
6
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇
: Solder
DISASSEMBLY
1
#177 X 1
Back View
#177
Note 2: Do not reuse the Radiation Sheet (CD) (500) because its
adhesive force decreases when it is removed once.
Note 3: Refer to “Assembly-5: Notes on assembling the lens block”
when assembling.
Note 2: Radiation Sheet (CD) (500) は一度剥がすと粘着力が弱くなる
ため、再利用はしないでください。
Note 3: 組立時は Assembly-5: Notes on assembling the lens block を
参照してください。
Note 4: When this part is removed, adjustment is required.
For the adjustment method, refer to “Adjustment items after
replacing parts” in the Note tab of the Adjust manual.
replacing parts” in the Note tab of the Adjust manual.
Note 4: この部品を取り外したときは調整が必要です。
調整方法については Adjust manual の Noteタブにある Adjust-
ment items after replacing parts を参照してください。
Note 5: Refer to “1-3. NOTES ON REMOVING/INSTALLING THE
IMAGER BOARD (CD-847 FLEXIBLE BOARD)”.
Note 5: 1-3. イメージャ基板 (CD-847フレキシブル基板) の取り外し/
取り付け時の注意 を参照してください。
SELECTION PARTS
Ref. No.55
These parts are provided for shift and tilt adjustment.
Change the thickness (t) according to result of adjustment.
Change the thickness (t) according to result of adjustment.
Note 6: Be sure to read “Precautions for Replacement of Imager” on
page 6-1 of Level 3 when changing the imager.
Note 6: イメージャの交換時はLevel 3の6-1ページ、 イメージャ交
換時の注意 を必ずお読みください。
DISCHARGING OF THE CHARGING CAPACITOR
51
53
#177
#257
#257
ns
SP901
(Note 8)
(Note 8)
#247
(Note 7)
#247
(Note 7)
Claw
2
4
3
1
54
5
52
ANT601
(Note 8)
(Note 8)
ANT801
(Note 8)
(Note 8)
ns
#302
ns
60
(Note 2)
56
57
58
59
6
Lens Block Section
(See page 2-9)
55
55
61
(Note 1, 3, 4)
BTH Block Section
(See page 2-6)
(including CP001
(CMOS imager))
(Note 4, 5, 6)
(CMOS imager))
(Note 4, 5, 6)
Before installing the SY-1021 board to
the main body, connect the flexible board
on the front side.
the main body, connect the flexible board
on the front side.
3
#247 X 2
#247
Left View
5
#257 X 2
#257
Back View
Screw
#177: M1.4 X 2.5
(Red)
3-208-537-21
3-208-537-21
2.5
1.4
#247: M1.4 X 2.5
(Black)
4-412-769-11
4-412-769-11
2.5
1.4
#257: M1.4 X 3.5
(Red)
3-208-537-41
3-208-537-41
1.4
3.5
Note
Note 1 :
Hold the Lens Block at the
center of both sides.
Do not hold the following part.
Hold here.
NOTES ON HOLDING THE LENS BLOCK
Lens Barrier
Very weak
Zoom Motor
Very weak
Focus Lens
Very weak
Note 7: This screw cannot be reused. Discard the screw removed
once in servicing. Instead, use a new screw.
Note 7:
このねじは再利用することができません。サービス対応時に
一度でも外した場合は新品のねじと交換してください。
Note 8: Refer to “Assembly-1: Notes on installing the speaker and
antennas” when assembling.
Note 8: 組立時は Assembly-1: Notes on installing the speaker and
antennas を参照してください。
4-410-539-01
SPACER PLATE (A) (t=0.10)
4-410-539-11
SPACER PLATE (A) (t=0.11)
4-410-539-21
SPACER PLATE (A) (t=0.12)
4-410-539-31
SPACER PLATE (A) (t=0.13)
4-410-539-41
SPACER PLATE (A) (t=0.14)
4-410-539-51
SPACER PLATE (A) (t=0.15)
4-410-539-61
SPACER PLATE (A) (t=0.16)
4-410-539-71
SPACER PLATE (A) (t=0.17)
4-410-539-81
SPACER PLATE (A) (t=0.18)
4-410-539-91
SPACER PLATE (A) (t=0.19)
4-410-540-01
SPACER PLATE (B) (t=0.20)
4-410-540-11
SPACER PLATE (B) (t=0.21)
4-410-540-21
SPACER PLATE (B) (t=0.22)
4-410-540-31
SPACER PLATE (B) (t=0.23)
4-410-540-41
SPACER PLATE (B) (t=0.24)
4-410-540-51
SPACER PLATE (B) (t=0.25)
4-410-540-61 SPACER PLATE (B) (t=0.26)
4-410-540-71 SPACER PLATE (B) (t=0.27)
4-410-540-81 SPACER PLATE (B) (t=0.28)
4-410-540-91 SPACER PLATE (B) (t=0.29)
4-437-388-01 SPACER PLATE C (t=0.30)
4-410-540-71 SPACER PLATE (B) (t=0.27)
4-410-540-81 SPACER PLATE (B) (t=0.28)
4-410-540-91 SPACER PLATE (B) (t=0.29)
4-437-388-01 SPACER PLATE C (t=0.30)
#302: M1.4 X 3.5
3.5
1.4
(Silver)
3-703-816-18
3-703-816-18
Click on the first or last page to see other DSC-RX100M2 (serv.man2) service manuals if exist.