DSC-RX1, DSC-RX1R (serv.man2) - Sony Digital Camera Service Manual (repair manual). Page 4

DSC-RX1/RX1R_L2

1-1

When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.

When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data. 
The data getting for this model is as follows.

• PRODUCT ID & USB SERIAL No.
• Angular Velocity Sensor Sensitivity adjustment
• AWB standard data input & check, Color reproduction check
• Strobe adjustment
• Lens data carry

PlayMemories Home has been written in internal memory.
The SY-1001 board for service is supplied with PlayMemories Home pre-installed.

The unit is shipped after an ID (USB Serial No.) unique to each unit and an ID (Product ID) unique to each model have been written.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID & USB 
SERIAL No. INPUT” and enter these IDs.

Note:  A newly entered Product ID is not always equal to the ID before board replacement. If the new ID differs from the previous ID, it may cause a difference 

from the ID registered by the customer.

When replacing the main board, read the QR code given on the Data Carry QR Seal attached to the JK-1002 Flexible Board.
Start the Adjust Manual and read the QR code using a QR code reader.
To read data from the main board, execute [Lens data carry] on the ADJUST tab of the Adjust Manual and read the previous data before the main board 
is replaced using [ORIGINAL DATA READ AND SAVE].
The read data is used for adjustment after replacement. When adjustment, execute [LOAD] from [Lens data carry] on the ADJUST tab of the Adjust 
Manual.

When replacing the lens, read the QR code given on the data sheet of the replacement 
lens for service.
Remove the Data Carry QR Seal and stick it to the JK-1002 Flexible Board. (For details, 
refer to “Assembly-1: Notes on Assembling the IM Imager Unit and Lens Block.”)
Start the Adjust Manual and read the QR code using a QR code reader.
The read data is used for adjustment after replacement. When adjustments, Select [Lens 
data carry] on the ADJUST tab of the Adjust Manual, and click the [LOAD] button to 
load the file.

Data carry QR seal

With the following features, this unit is likely to capture foreign particles.

• The imager sensor size is large.
• The space between the imager sensor and the lens is small.

Therefore, pay close attention to foreign particles.

1)   When replacing the LSV-1600A Device or the IM Imager Unit, read values from the IM Data Carry Seal and the Lens Data Carry QR Seal shown 

in the figure below, and then write down the read values.

 

Lens data carry QR seal

IM data carry seal

Lens data carry QR seal 
(Describing lens tilting amount)

IM data carry seal  
(Describing imager tilting amount) 

00000014

-14.77   10.30

1058300067

X -5.8 

Y

 +0.7

2)  Start “Shim Selection Tool Ver_[].[].exe.”
 

Enter each recorded value into “Shim Selection Tool Ver_[].[].exe” according to the figure below, and then click [OK].

Note: Download “Shim Selection Tool Ver_[].[].exe” from the TISS homepage.

 

Lens data carry QR seal

IM data carry seal

Enter the values provided on the seats attached to the lens block
and the rear tube. Then click the [OK] button.

1058300067

X -5.8  Y +0.7

00000014

-14.77   10.30