DSC-RX1, DSC-RX1R (serv.man2) - Sony Digital Camera Service Manual (repair manual)

dsc-rx1, dsc-rx1r (serv.man2) service manual
Model
DSC-RX1 DSC-RX1R (serv.man2)
Pages
28
Size
6.86 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / LEVEL 2
File
dsc-rx1-dsc-rx1r-sm2.pdf
Date

Read Sony DSC-RX1 / DSC-RX1R (serv.man2) Service Manual online

DSC-RX1/RX1R_L2
Sony Corporation
SERVICE MANUAL
Revision History
SERVICE  NOTE (Check the following note before the service.)
LEVEL 
2
Published by Sony Techno Create Corporation
983473831.pdf
DIGITAL STILL CAMERA
The components identified by 
mark 
0 or dotted line with mark 
0 are critical for safety.
Replace only with part number 
specified.
Les composants identifiés par 
une marque 
0 sont critiques pour 
la sécurité.
Ne les remplacer que par une piè-
ce portant le numéro spécifié.
US Model
Canadian Model
AEP Model
E Model
Chinese Model
Japanese Model
9-834-738-31
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
2013.06
Official Release
2013F08-1
  © 2013.06
– ENGLISH –
1-1.  NOTES ON REPLACING THE SY-1001 BOARD
1-2.  NOTES ON REPLACING THE LENS
1-3.  NOTES ON REMOVING/INSTALLING THE IMAGER BOARD
1-4.  NOTES ON REPLACING THE LSV-1600A DEVICE AND IM IMAGER UNIT
1-5.  ADDITION OF DESTINATION DATA FILE
1-6. SELF-DIAGNOSIS 
FUNCTION
1-7.  PROCESS AFTER FIXING FLASH ERROR
– JAPANESE –
1-1.  SY-1001基板交換時の注意
1-2.  レンズ交換時の注意
1-3.  イメージャ基板の取り外し/取り付け時の注意
1-4.  LSV-1600Aデバイスおよび IMイメージャーユニット交換時の注意
1-5.  Destination Dataファイルの追加について
1-6.  自己診断機能
1-7.  フラッシュエラー発生時の対処法
Ver. 1.0  2013.06
DSC-RX1/RX1R
Photo: DSC-RX1
Note: This manual contains information of the DSC-RX1 Service Manual (9-834-697-[][]) and additional DSC-RX1R information.
Note: 
このマニュアルはDSC-RX1のサービスマニュアル(9-834-697-[][])にDSC-RX1Rの情報を追加したものです。
DSC-RX1/RX1R_L2
– 2 –
SPECIFICATIONS
概略仕様
– ENGLISH –
– JAPANESE –
Camera
[System]
Image device: 35mm full size
 
(35.8 mm × 23.9 mm), Exmor
 
CMOS image sensor
Total pixel number of camera:
 
Approx. 24.7 Megapixels
Effective pixel number of camera:
 
Approx. 24.3 Megapixels
Lens: Carl Zeiss Sonnar T*
 
35mm single focus lens
 
f = 35 mm, F2.0
 
While shooting movies (16:9):
 
When [SteadyShot] is set to
 
[Off]: 37 mm
 
When [SteadyShot] is set to [On]:
 44 
mm
 
While shooting movies (4:3):
 
When [SteadyShot] is set to
 
[Off]: 45 mm
 
When [SteadyShot] is set to [On]:
 48 
mm
 Minimum 
focus
*1
:
 
When the macro switching ring is
 
set to “0,3m- ”: 0.3 m (1 ft.)
 
When the macro switching ring is
 
set to “0,2m-0,35m”: 0.2 m
 (0.65 
ft.)
*1
 Minimum focus is the shortest distance 
from the image sensor to the subject.
 Maximum 
magnification:
 
When the macro switching ring is
 
set to “0,3m- ”: 0.15×
 
When the macro switching ring is
 
set to “0,2m-0,35m”: 0.26×
 
Minimum f-stop: F22
 
Filter diameter: 49 mm
SteadyShot: Electronic (only for
 movies)
Exposure control: Automatic
 exposure, 
Aperture 
priority,
 
Shutter priority, Manual
 
exposure, Scene Selection
 (7 
modes)
White balance: Automatic, Daylight,
 
Shade, Cloudy, Incandescent,
 Fluorescent 
(Warm 
White/
 
Cool White/Day White/Daylight),
 
Flash, Color temperature/Color
 filter, 
Custom
Signal format:
 
For 1080 50i:
 
PAL color, CCIR standards
 
HDTV 1080/50i, 1080/50p
 specification
 
For 1080 60i:
 
NTSC color, EIA standards
 
HDTV 1080/60i, 1080/60p
 specification
File format:
 
Still images: JPEG (DCF, Exif,
 
MPF Baseline) compliant, RAW
 
(Sony ARW 2.3 Format), DPOF
 compatible
 
Movies (AVCHD format):
 
AVCHD format Ver. 2.0
 compatible
 Video: 
MPEG-4 
AVC/H.264
 
Audio: Dolby Digital 2ch,
 
equipped with Dolby Digital
 Stereo 
Creator
•  Manufactured under license from Dolby 
Laboratories.
 
Movies (MP4 format):
 Video: 
MPEG-4 
AVC/H.264
 
Audio: MPEG-4 AAC-LC 2ch
Recording media: “Memory Stick
 
Duo” media, “Memory Stick
 
Micro” media, SD cards,
 
microSD memory cards
Flash: Flash range (ISO sensitivity
 
(Recommended Exposure Index)
 set 
to 
Auto):
 
Approx. 0.75 m to 21.7 m
 
(2.5 ft. to 71.2 ft.)
[Input and Output connectors]
HDMI connector: HDMI micro jack
Micro USB connector:
 USB 
communication
Microphone jack: 
φ3.5 mm Stereo
 mini 
jack
USB communication: Hi-Speed USB
 (USB 
2.0)
[Screen]
LCD screen:
 
7.5 cm (3.0 type) TFT drive
Total number of dots:
 
1 228 800 dots
[Power, general]
Power: Rechargeable battery pack
 NP-BX1, 
3.6 
V
 
AC Adaptor AC-UD10/UD11,
 5 
V
Power consumption (during
 shooting): 
2.0 
W
Operating temperature: 0 °C to 40 °C
 
(32 °F to 104 °F)
Storage temperature: –20 °C to
 
+60 °C (–4 °F to +140 °F)
Dimensions (CIPA compliant):
 
113.3 mm × 65.4 mm × 69.6 mm
 
(4 1/2 inches × 2 5/8 inches ×
 
2 3/4 inches) (W/H/D)
Mass (CIPA compliant) (including
 
NP-BX1 battery pack, “Memory
 
Stick Duo” media):
 
Approx. 482 g (17 oz)
Microphone: Stereo
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III:
 Compatible
AC Adaptor AC-UD10/UD11
Power requirements: AC 100 V to
 
240 V, 50 Hz/60 Hz, 0.2 A
Output voltage: DC 5 V, 1 500 mA
Operating temperature: 0 °C to 40 °C
 
(32 °F to 104 °F)
Storage temperature: –20 °C to
 
+60 °C (–4 °F to +140 °F)
Dimensions:
 
AC-UD10: Approx. 78 mm ×
 
22 mm × 36 mm (3 1/8 inches ×
 
7/8 inches × 1 7/16 inches)
 (W/H/D)
 
AC-UD11: Approx. 70 mm ×
 
33 mm × 36 mm (2 7/8 inches ×
 
1 5/16 inches × 1 7/16 inches)
 (W/H/D)
Mass:
 
AC-UD10: Approx. 45 g (1.6 oz)
 
AC-UD11: Approx. 50 g (1.8 oz)
Rechargeable battery pack
NP-BX1
Used battery: Lithium-ion battery
Maximum voltage: DC 4.2 V
Nominal voltage: DC 3.6 V
Maximum charge voltage: DC 4.2 V
Maximum charge current: 1.89 A
Capacity: 4.5 Wh (1 240 mAh)
Design and specifications are
subject to change without notice.
本体
[システム]
撮像素子:
35mm
フルサイズ
 
35.8 mm
×
23.9 mm
)、
 Exmor 
CMOS
イメージセンサー
総画素数:約
2470
万画素
カメラ有効画素数:約
2430
万画素
レンズ:
 
カール
 
ツァイス
 
ゾナー
T *
 35mm
単焦点レンズ
 f=35 
mm
F2.0
 
動画撮影時(
16
9
):
 
[手ブレ補正]が[
 
切]:
37 mm
 
[手ブレ補正]が[
 
入]:
44 mm
 
動画撮影時(
4
3
):
 
[手ブレ補正]が[
 
切]:
45 mm
 
[手ブレ補正]が[
 
入]:
48 mm
 
最短撮影距離
*1
 
マクロ切り換えリングが
 
0,3m-
∞」:
0.3 m
 
マクロ切り換えリングが
 
0,2m-0,35m
」:
0.2 m
*1
 
最短撮影距離とはイメージセンサー位置表示
から被写体までの距離を表します。
 
最大撮影倍率:
 
マクロ切り換えリングが
 
0,3m-
∞」:
0.15
 
マクロ切り換えリングが
 
0,2m-0,35m
」:
0.26
 
最小絞り:
F22
 
フィルター径:
49 mm
手ブレ補正:電子式(動画時のみ)
露出制御:自動、絞り優先、
 
シャッタースピード優先、マニュアル露出、
 
シーンセレクション(
7
モード)
ホワイトバランス:オート
/
太陽光
/
 
日陰
/
曇天
/
電球
/
蛍光灯(温白色
/
 
白色
/
昼白色
/
昼光色)
/
 
フラッシュ
/
色温度・
 
カラーフィルター
/
カスタム
信号方式:
NTSC
カラー、
EIA
標準方式
記録方式:
 
静止画記録方式:
 JPEG
DCF
Exif
MPF Baseline
)準拠、
 RAW
(ソニー
ARW 2.3
フォーマット)、
 DPOF
対応
 
動画記録方式(
AVCHD
方式):
 AVCHD
規格
 Ver.2.0
準拠
 
映像:
MPEG-4 AVC/H.264
 
音声:
Dolby Digital 2ch
 
ドルビーデジタルステレオクリエーター搭載
• 
ドルビーラボラトリーズからの実施権に基づき
製造されています。
 
動画記録方式(
MP4
方式):
 
映像:
MPEG-4 AVC/H.264
 
音声:
MPEG-4 AAC-LC 2ch
記録メディア:
 
“メモリースティック
 
デュオ”、
 
“メモリースティック
 
マイクロ”、
 SD
カード、
microSD 
メモリーカード
フラッシュ:撮影範囲(
ISO
感度(推奨
 
露光指数)がオートのとき)
 
0.75 
m∼
 21.7 m
[入出力端子]
HDMI
端子:
HDMI
マイクロ端子
マイクロ
USB
端子:
USB
通信
MIC
(マイク)端子:
ø3.5 mm
ステレ
 
オミニジャック
USB
通信:
Hi-Speed USB
USB 2.0
[モニター]
液晶モニター:
 7.5 
cm
3.0
型)、
TFT
駆動
総ドット数:
1 228 800
ドット
[電源・その他]
電源:リチャージャブルバッテリー
 
パック
NP-BX1
3.6 V
 AC
アダプター
 AC-UD11
5 V
消費電力(撮影時):約
2.0 W
動作温度:
℃∼
 40 
保存温度:−
20 
℃∼
 +60 
外形寸法(
CIPA
準拠):
 113.3 
mm
×
65.4 mm
×
69.6 mm
 
(幅×高さ×奥行き)
本体質量(
CIPA
準拠)
 
(バッテリー
NP-BX1
、“メモリース
 
ティック
 
デュオ”を含む):
 
482 g
マイクロホン:ステレオ
スピーカー:モノラル
Exif Print
:対応
PRINT Image Matching III
:対応
ACアダプター AC-UD11
定格入力:
AC 100 V 
 240 V
 
50 Hz/60 Hz
0.2 A
定格出力:
DC 5 V
1 500 
A
動作温度:
℃∼
 40 
保存温度:−
20 
℃∼
 +60 
外形寸法:約
70 mm
×
33 mm
×
 36 
mm
(幅×高さ×奥行き)
本体質量:約
50 g
リチャージャブルバッテリー
パックNP-BX1
使用電池:リチウムイオン蓄電池
最大電圧:
DC 4.2 V
公称電圧:
DC 3.6 V
容量:
4.5 Wh
1 240 mAh
本機や付属品の仕様および外観は、改良のため予告
なく変更することがありますが、ご了承ください。
Model information table
Model
DSC-RX1
DSC-RX1R
Destination
US, CND, E, J
AEP, E, CH
US, CND, E, J
AEP, E, CH
Color system
NTSC
PAL
NTSC
PAL
GPS
• Abbreviation
  CH :  Chinese model
  CND :  Canadian model
  J : 
Japanese model
DSC-RX1/RX1R_L2
– 3 –
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH 
MARK 
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST 
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS 
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY 
SONY. 
ATTENTION AU  COMPOSANT  AYANT  RAPPORT 
À  LA  SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES 
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT 
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT 
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES 
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は,正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は,取扱指示に従って処分してください。
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free 
mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with the 
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
•   Set the soldering iron tip temperature to 350 °C approximately. 
If cannot control temperature, solder/unsolder at high temperature 
for a short time.
Caution:  The printed pattern (copper foil) may peel away if the 
heated tip is applied for too long, so be careful!  
Unleaded solder is more viscous (sticky, less prone to 
flow) than ordinary solder so use caution not to let solder 
bridges occur such as on IC pins, etc.
•   Be sure to control soldering iron tips used for unleaded solder and 
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the following 
safety checks before releasing the set to the customer.
1.  Check the area of your repair for unsoldered or poorly-soldered 
connections. Check the entire board surface for solder splashes and 
bridges.
2.  Check the interboard wiring to ensure that no wires are “pinched” 
or contact high-wattage resistors.
3.  Look for unauthorized replacement parts, particularly transistors, 
that were installed during a previous repair. Point them out to the 
customer and recommend their replacement.
4.  Look for parts which, through functioning, show obvious signs of 
deterioration. Point them out to the customer and recommend their 
replacement.
5.  Check the B+ voltage to see it is at the values specified.
6.  Flexible Circuit Board Repairing
 
•   Set the soldering iron tip temperature to 350 °C approximately.
 
•   Do not touch the soldering iron on the same conductor of the circuit 
board (within 3 times).
 
•   Be careful not to apply force on the conductor when soldering or 
unsoldering.
1.  注意事項をお守りください。
 
サービスのとき特に注意を要する個所については,キャビ
ネット,シャーシ,部品などにラベルや捺印で注意事項を
表示しています。これらの注意書き及び取扱説明書等の注
意事項を必ずお守り下さい。
2.  指定部品のご使用を
 
セットの部品は難燃性や耐電圧など安全上の特性を持った
ものとなっています。従って交換部品は,使用されていた
ものと同じ特性の部品を使用して下さい。特に回路図,部
品表に0印で指定されている安全上重要な部品は必ず指定
のものをご使用下さい。
3.  部品の取付けや配線の引きまわしはもとどおりに
 
安全上,チューブやテープなどの絶縁材料を使用したり,
プリント基板から浮かして取付けた部品があります。また
内部配線は引きまわしやクランパによって発熱部品や高圧
部品に接近しないよう配慮されていますので,これらは必
ずもとどおりにして下さい。
4.  サービス後は安全点検を
 
サービスのために取外したネジ,部品,配線がもとどおり
になっているか,またサービスした個所の周辺を劣化させ
てしまったところがないかなどを点検し,安全性が確保さ
れていることを確認して下さい。
5.  チップ部品交換時の注意
 
・  取外した部品は再使用しないで下さい。
 
・  タンタルコンデンサのマイナス側は熱に弱いため交換時
は注意して下さい。
6.  フレキシブルプリント基板の取扱いについて
 
・  半田こてのこて先温度は約350℃に設定してください。
 
・  同一パターンに何度もコテ先を当てないで下さい。(3回
以内)
 
・  パターンに力が加わらないよう注意して下さい。
サービス,点検時には次のことにご注意ください。
無鉛半田について
本機には無鉛半田が使用されています。
無鉛半田を使用している基板には,無鉛(Lead Free)を意味する
レッドフリーマークがプリントされています。
(注意: 基板サイズによっては,無鉛半田を使用していてもレッ
ドフリーマークがプリントされていないものがありま
す)
:レッドフリーマーク
無鉛半田は,下記の点に注意して使用してください。
・  半田こてのこて先温度は約350℃に設定してください。
温度調節が無理な場合は,高温短時間で作業を行ってくだ
さい。
注意:  半田こてを長く当てすぎると,基板のパターン(銅
箔)がはがれてしまうことがありますので,注意して
ください。また,従来の半田よりも粘性が強いため,
IC端子などが半田ブリッジしないように注意してく
ださい。
・  半田こてのこて先は,必ず無鉛半田用と有鉛半田用に分け
て管理してください。
無鉛半田と有鉛半田が混在すると剥離現象が発生してしま
います。
– ENGLISH –
– JAPANESE –
注意
如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
DSC-RX1/RX1R_L2
1-1
1. SERVICE  NOTE
1-1.  NOTES ON REPLACING THE SY-1001 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
RESTORE DATA
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data. 
The data getting for this model is as follows.
• PRODUCT ID & USB SERIAL No.
• Angular Velocity Sensor Sensitivity adjustment
• AWB standard data input & check, Color reproduction check
• Strobe adjustment
• Lens data carry
Regarding the PlayMemories Home
PlayMemories Home has been written in internal memory.
The SY-1001 board for service is supplied with PlayMemories Home pre-installed.
USB Serial No. and Product ID
The unit is shipped after an ID (USB Serial No.) unique to each unit and an ID (Product ID) unique to each model have been written.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID & USB 
SERIAL No. INPUT” and enter these IDs.
Note:  A newly entered Product ID is not always equal to the ID before board replacement. If the new ID differs from the previous ID, it may cause a difference 
from the ID registered by the customer.
Lens Data Carry
When replacing the main board, read the QR code given on the Data Carry QR Seal attached to the JK-1002 Flexible Board.
Start the Adjust Manual and read the QR code using a QR code reader.
To read data from the main board, execute [Lens data carry] on the ADJUST tab of the Adjust Manual and read the previous data before the main board 
is replaced using [ORIGINAL DATA READ AND SAVE].
The read data is used for adjustment after replacement. When adjustment, execute [LOAD] from [Lens data carry] on the ADJUST tab of the Adjust 
Manual.
1-2.  NOTES ON REPLACING THE LENS
When replacing the lens, read the QR code given on the data sheet of the replacement 
lens for service.
Remove the Data Carry QR Seal and stick it to the JK-1002 Flexible Board. (For details, 
refer to “Assembly-1: Notes on Assembling the IM Imager Unit and Lens Block.”)
Start the Adjust Manual and read the QR code using a QR code reader.
The read data is used for adjustment after replacement. When adjustments, Select [Lens 
data carry] on the ADJUST tab of the Adjust Manual, and click the [LOAD] button to 
load the file.
Data carry QR seal
– ENGLISH –
1-3.  NOTES ON REMOVING/INSTALLING THE IMAGER BOARD
With the following features, this unit is likely to capture foreign particles.
• The imager sensor size is large.
• The space between the imager sensor and the lens is small.
Therefore, pay close attention to foreign particles.
1-4.  NOTES ON REPLACING THE LSV-1600A DEVICE AND THE IM IMAGER UNIT
1)   When replacing the LSV-1600A Device or the IM Imager Unit, read values from the IM Data Carry Seal and the Lens Data Carry QR Seal shown 
in the figure below, and then write down the read values.
 
Lens data carry QR seal
IM data carry seal
Lens data carry QR seal 
(Describing lens tilting amount)
IM data carry seal  
(Describing imager tilting amount) 
00000014
-14.77   10.30
1058300067
X -5.8 
Y
 +0.7
2)  Start “Shim Selection Tool Ver_[].[].exe.”
 
Enter each recorded value into “Shim Selection Tool Ver_[].[].exe” according to the figure below, and then click [OK].
Note: Download “Shim Selection Tool Ver_[].[].exe” from the TISS homepage.
 
Lens data carry QR seal
IM data carry seal
Enter the values provided on the seats attached to the lens block
and the rear tube. Then click the [OK] button.
1058300067
X -5.8  Y +0.7
00000014
-14.77   10.30
Page of 28
Display

Download Sony DSC-RX1 / DSC-RX1R (serv.man2) Service Manual (Repair Manual)

Here you can read online and download Sony DSC-RX1 / DSC-RX1R (serv.man2) Service Manual in PDF. DSC-RX1 / DSC-RX1R (serv.man2) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sony DSC-RX1 / DSC-RX1R (serv.man2) Digital Camera. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.