Read Sony DSC-P50 Service Manual online
4-1
SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
DSC-P50
(For printed wiring boards)
•
•
: Uses unleaded solder.
•
b
: Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated)
• Through hole is omitted.
• Circled numbers refer to waveforms.
• There are a few cases that the part printed on diagram
• Circled numbers refer to waveforms.
• There are a few cases that the part printed on diagram
isn’t mounted in this model.
• Chip parts.
(For schematic diagrams)
• All capacitors are in
• All capacitors are in
µ
F unless otherwise noted. pF :
µ
µ
F. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
k
Ω
=1000
Ω
, M
Ω
=1000 k
Ω
.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
In such cases, the unused circuits may be indicated.
• Parts with
★
differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT
→
EDIT
PB/XREC
→
PB/REC
•
2
: non flammable resistor
•
1
: fusible resistor
•
C
: panel designation
•
A
: B+ Line
*
•
B
: B– Line
*
•
J
: IN/OUT direction of (+,–) B LINE.
*
•
C
: adjustment for repair.
*
• Circled numbers refer to waveforms.
*
*
Indicated by the color red.
Note :
The components identified by mark
0
or
dotted line with mark
0
are critical for safety.
Replace only with part number specified.
Note :
Les composants identifiés par une marque
0
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifie.
le numéro spécifie.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values
and reference waveforms.
color bar chart of pattern box. They are reference values
and reference waveforms.
*
(VOM of DC 10 M
Ω
input impedance is used)
• Voltage values change depending upon input impedance
of VOM used.)
1. Connection
2. Adjust the distance so that the output waveform of Fig.
a and the Fig. b can be obtain.
When indicating parts by reference number, please
include the board name.
include the board name.
Y
ello
w
A
A
B
B
A=B
H
Cy
an
Green
White
Magenta
Red
Blue
Fig. a (Video output terminal waveform)
Fig.b (Picture on monitor TV)
Color bar chart
picture frame
picture frame
Monitor TV
picture frame
picture frame
Green
Y
ello
w
Cy
an
White
Magenta
Red
Blue
THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(In addition to this, the necessary note is printed in each block)
Kinds of capacitor
Temperature characteristics
External dimensions (mm)
1
2
3
6
5
4
E
B
C
3
1
5
5
2
4
6
5
4
3
1
2
Transistor
2
1
3
2
1
3
2
1
3
3
4
5
2
1
3
2
1
4
5
Diode
1
2
4
3
Front of the lens
Pattern box
L
L=About 90 cm
Click on the first or last page to see other DSC-P50 service manuals if exist.