Read Sony DSC-HX300 (serv.man2) Service Manual online
DSC-HX300_L2
2-6
2-1-4. ST/BT SECTION
ns : not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
151
4-458-108-01
COVER (490), ST
152
4-458-111-01
PLATE (490), MODE
153
1-492-119-11
SWITCH BLOCK, CONTROL (SW63490) (Note
1
)
154
A-1926-865-A ST-1013 BOARD, COMPLETE
155
1-887-722-11
BT-2005 FLEXIBLE BOARD
156
4-177-693-01
SPRING, BT DISCHARGE
157
X-2586-759-1 BTH
ASSY
(490)
158
X-2586-765-1 ST
ASSY
(490)
159
1-888-083-11
HB-1002 FLEXIBLE BOARD
160
4-458-102-01
CUSHION (490), MICROPHONE
161
4-458-101-01
PLATE (MIC) (490), GROUND
162
A-1926-871-A FP-2130 FLEXIBLE BOARD, COMPLETE
(Note 2)
163
1-490-083-11
FLASH UNIT
164
1-969-004-11
HARNESS (SK-1003) (Orange)
165
1-969-002-11
HARNESS (SK-1001) (Pink)
166
1-969-003-11
HARNESS (SK-1002) (White)
167
4-464-016-01
CUSHION (ST) (490)
168
CAUTION
SHEET (GROUND PLATE MIC) (490)
(Note 2)
*BT001 1-780-826-11
TERMINAL BOARD, BATTERY
C901
1-118-589-11
CAP, ALUMINIUM ELECT 134uF 315V
MIC901 1-542-967-11 MICROPHONE
UNIT
#12
3-080-204-21 SCREW,
TAPPING,
P2
#108
2-695-430-01
SCREW (T1.7), HEAD PAN TAPPING
#257
3-208-537-41
0+Z M1.4X2 NEW TORASUTA
#292 3-316-938-41 SCREW
(B1.4X6),
TAPPING
1. Remove in numerical order (
1
to
4
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇
: Solder
DISASSEMBLY
Note 2:
Note 2:
4
158
3
151
2
153
(Note
1
)
152
155
156
157
164
(Orange)
165
(Pink)
166
(White)
160
161
162
(Note 2)
154
163
167
159
#12
#12
#108
MIC901
#108
#12
#257
ns
C901
ns
BT001
#292
1
1
Front Section
(See page 2-7)
(Size: 10.0mm X 5.0mm)
(Note 2)
(Note 2)
検出スイッチ
FP-2130
フレキ
接着紙 (アース板Mic) (490)
168
Pay attention not to bend the FP-2130 flexible board when installing it.
If the FP-2130 flexible board is bent, it separates from the adhesion part
and the detection switch does not function normally.
If the FP-2130 flexible board is bent, it separates from the adhesion part
and the detection switch does not function normally.
Detection switch
FP-2130 flexible board
Sheet (ground plate mic) (490)
組立時にFP-2130フレキを曲げないように注意してください。
FP-2130フレキが接着部から浮いてしまい, 検出スイッチが正常に動作しな
くなります。
FP-2130フレキが接着部から浮いてしまい, 検出スイッチが正常に動作しな
くなります。
Note
Note
1
: Refer to “Assembly-1: Notes on Assembling the Control Switch
Block (SW63490)” when assembling.
Screw
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
#108: M1.7 X 3.0 (Tapping)
(Black)
2-695-430-01
2-695-430-01
3.0
1.7
Note
1
: 組立時は Assembly-1: Notes on Assembling the Control
Switch Block (SW63490) を参照してください。
1
#12 X 2 → Pull out the BT Block (
1
)
Back View
1
#12
2
#12 X 2 → Remove the Control Switch Block
Buttons
Ribs
Back View
#12
3
Pop up the Strobe (
3
) → #108 X 1
Right View
3
#108
4
#108 X 2 → Push the Grill (
4
-1
) → Disengage two bosses (
4
-2
) → Remove the ST Block
ST Block
Grill
Bosses
Back View
4-1
4-2
#108
#257: M1.4 X 3.5
(Red)
3-208-537-41
3-208-537-41
1.4
3.5
#292: M1.4 X 6.0 (Tapping)
(Black)
4-188-736-21
4-188-736-21
6.0
1.4
DISCHARGING OF THE
CHARGING CAPACITOR
ストロボ用充電コンデンサの放電
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2013.05
CAUTION
For the part of 168 : SHEET (GROUND PLATE MIC) (490), if it has
the adhesion, reuse it again. IF not, cut the SHEET, ADHESIVE
(4-441-672-01) into the desired length and use it.
the adhesion, reuse it again. IF not, cut the SHEET, ADHESIVE
(4-441-672-01) into the desired length and use it.
注意
168 : SHEET (GROUND PLATE MIC) (490) は、粘着力が残っていれば
再利用し、粘着力が残っていない場合は、SHEET, ADHESIVE (4-441-
672-01) を切って使用すること。
再利用し、粘着力が残っていない場合は、SHEET, ADHESIVE (4-441-
672-01) を切って使用すること。
Click on the first or last page to see other DSC-HX300 (serv.man2) service manuals if exist.