Read Sony DSC-HX10 / DSC-HX10V (serv.man2) Service Manual online
DSC-HX10/HX10V_L2
2-6
157
A-1851-207-A LINEAR GUIDE TUBE A ASSY (SILVER, WHITE)
158
A-1802-347-A NARUTO GEAR LUBRICATED ASSY
159
A-1802-348-A GEAR
CASE
ASSY
160
1-856-183-31
FILTER BLOCK, OPTICAL
161
4-209-570-01
SEAL RUBBER (1470)
162
A-1861-491-A CD-839 FLEXIBLE BOARD, COMPLETE
(including CP001 (CMOS imager)) (Note 3)
#30
3-086-156-11 SCREW
B1.2
151
8-848-891-01
DEVICE, LENS LSV-1470B-BK (BLACK, RED)
(Note 1, 2
, 4
)
151
8-848-891-11
DEVICE, LENS LSV-1470B-LS (SILVER, WHITE)
(Note 1, 2
, 4
)
152
4-299-835-02
RING (A), ORNAMENTAL (BLACK, RED)
152
4-299-835-12
RING (A), ORNAMENTAL (SILVER, WHITE)
153
4-208-132-02 TAPE,
BARRIER
154
A-1802-316-A BARRIER ASSY (BLACK, RED)
154
A-1851-204-A BARRIER ASSY (SILVER, WHITE)
155
A-1802-357-A CAM
TUBE
LUBRICATED
ASSY
156
A-1802-356-A LINEAR GUIDE TUBE B LUBRICATED
157
A-1802-354-A LINEAR GUIDE TUBE A ASSY (BLACK, RED)
2-1-4. LENS BLOCK SECTION
ns : not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
#30
#30
#30
ns
ns
ns
ns
ns
ns
158
151
(Note 1, 2
, 4
)
162
(including CP001
(CMOS imager))
(Note 3)
(CMOS imager))
(Note 3)
159
ns
157
152
153
153
154
155
156
161
160
ns
1. The meaning of the sign in left figure is as follows. Be careful when it removes.
◇-X
: Solder
DISASSEMBLY
Screw
#30: M1.2 X 3.5 (Tapping)
(White)
3-086-156-11
3-086-156-11
3.5
1.2
Note
Note 1:
Hold the Lens Block at the
center of both sides.
center of both sides.
Do not hold the following part.
Hold here.
PRECAUTIONS WHEN HOLDING THE LENS BLOCK
Lens Barrier
Very weak
Zoom Motor
Very weak
Zoom Motor
Very weak
Focus Motor
Very weak
MR Magnet
Very weak
Focus Lens
Very weak
Sensor
Sensor
Note 2: Refer to the following each item when you exchange parts of
Lens Block.
• 1-8. ORNAMENTAL RING A OR BARRIER ASSY REPLAC-
ING METHOD (page 1-7)
• 1-9. CAM TUBE LUBRICATED ASSY REPLACING
(page
(page
1-8)
• 1-10. FINAL INSPECTION (page 1-13)
Note 2: レンズブロックの各部品を交換する際は,下記の各項目を参
照してください。
1-8.
ORNAMENTAL RING A OR BARRIER ASSY REPLACING
METHOD (page 1-7)
METHOD (page 1-7)
1-9.
CAM TUBE LUBRICATED ASSY REPLACING (page 1-8)
1-10. FINAL INSPECTION (page 1-13)
Note 3: Be sure to read "Precautions for Replacement of Imager" on
page 6-1 of Level 3 when changing t.he imager.
Note 3: イメージャの交換時はLevel3の6-1ページ、 イメージャ交換
時の注意 を必ずお読みください。
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2012.05
Note 4: When this part is removed, adjustment is required.
For the adjustment method, refer to "Adjustment items after
replacing parts" in the Note tab of the Adjust manual.
replacing parts" in the Note tab of the Adjust manual.
Note 4: この部品を取り外したときは調整が必要です。
調整方法については Adjust manual の Noteタブにある
Adjustment items after replacing parts を参照してください。
Adjustment items after replacing parts を参照してください。
Click on the first or last page to see other DSC-HX10 / DSC-HX10V (serv.man2) service manuals if exist.