Read Sony XR-CA665EE Service Manual online
23
XR-CA665EE
6-10.
IC PIN FUNCTION DESCRIPTION
•
MAIN BOARD IC501 MN101C49KSY (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
VREF–
I
Reference voltage (0V) input terminal (for A/D converter)
2
VSM
I
FM and AM signal meter voltage detection signal input from the tuner unit (A/D input)
3
NIL
I
Connected to the ground
4
KEYIN1
I
Front panel key input terminal (A/D input)
5
KEYIN0
I
Front panel key input terminal (A/D input)
6
RC_IN0
I
Rotary remote commander key input terminal (A/D input)
7
QUALITY
I
Noise level detection signal input at the SEEK mode (A/D input) Not used
8
NIL
I
Connected to the ground
9
DSTSEL
I
Destination setting terminal
10
VREF+
I
Reference voltage (+5V) input terminal (for A/D converter)
11
VDD
—
Power supply terminal (+5V)
12
OSC2
O
Main system clock output terminal (18.432 MHz)
13
OSC1
I
Main system clock input terminal (18.432 MHz)
14
VSS
—
Ground terminal
15
XI
I
Sub system clock input terminal (32.768 kHz)
16
XO
O
Sub system clock output terminal (32.768 kHz)
17
MMOD
I
Selection signal of memory mode input terminal
“L”: single chip mode (fixed at “L” in this set)
“L”: single chip mode (fixed at “L” in this set)
18
LCDSO
O
Serial data output to the liquid crystal display driver
19
LCDCE
O
Chip enable signal output to the liquid crystal display driver “H” active
20
LCDCKO
O
Serial data transfer clock signal output to the liquid crystal display driver
21 to 23
NCO
O
Not used
24
SYSRST
O
System reset signal output to the SONY bus interface “L”: reset
25
BUSON
O
Bus interface control signal output to the SONY bus interface “L”: bus on
26
KEYACK
I
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function
and eject keys in the power off status On at input of “H”
and eject keys in the power off status On at input of “H”
27
DAVN
I
Sync detection signal of RDS data block input terminal “H” active Not used
28
BU_IN
I
Battery detection signal input from the SONY bus interface “L” is input at low voltage
29
SIRCS
I
SIRCS remote control signal input from the remote control receiver
30
TUATT IN
I
Tuner muting on/off control signal input from the tuner unit “L”: muting on
31
NIL
I
Connected to the ground
32
NIH
I
Connected to the power supply (+5V)
33
RESET
I
System reset signal input from the reset signal generator and reset switch “L”: reset
For several hundreds sec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds sec. after the power supply rises, “L” is input, then it changes to “H”
34
TUNON
O
Tuner system power supply on/off control signal output terminal “H”: tuner power on
35
BEEP
O
Beep sound drive signal output to the power amplifier
36, 37
NCO
O
Not used
38
ACCIN
I
Accessory detection signal input terminal “L”: accessory on
39
NCO
O
Not used
40
TELATT
I
Telephone attenuate signal input terminal At input of “H”, the signal is attenuated by –20 dB
41
NIH
I
Connected to the power supply (+5V)
42
BUSSO
O
Serial data output to the SONY bus interface
43
BUSSI
I
Serial data input from the SONY bus interface
44
BUSCKO
O
Serial data transfer clock signal output to the SONY bus interface
45
I2CSIO
I/O
Two-way data bus with the tuner unit and electrical volume
Click on the first or last page to see other XR-CA665EE service manuals if exist.