Read Sony XM-GTR6001 Service Manual online
XM-GTR6001
2
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscou-s (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
Notes on chip component replacement
•
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
Confi rming the Operation
Please confi rm the car audio unit works even if REM output is not
connected when you connect this set with the car audio unit by the
HIGH LEVEL input.
Please confi rm the car audio unit works even if REM output is not
connected when you connect this set with the car audio unit by the
HIGH LEVEL input.
SAFETY-RELATED COMPONET WARNING!
COMPONENTS IDENTIFIED BY MARK
0 OR DOTTED LINE
WITH MARK
0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
1. GENERAL
Location and Function of Controls ...................................... 3
Connections.......................................................................... 4
2. DISASSEMBLY
2-1. Cover Assy ..................................................................... 9
2-2. Top Plate Section ............................................................. 10
2-3. MAIN Board Section ....................................................... 10
2-4. MAIN Board .................................................................... 11
2-5. LED PROT Board, LED ILLUMI Board ........................ 11
2-2. Top Plate Section ............................................................. 10
2-3. MAIN Board Section ....................................................... 10
2-4. MAIN Board .................................................................... 11
2-5. LED PROT Board, LED ILLUMI Board ........................ 11
3. DIAGRAMS
3-1. Block Diagram ................................................................. 13
3-2. Printed Wiring Boards –MAIN Section (1/2)– ................ 14
3-3. Printed Wiring Boards –MAIN Section (2/2)– ................ 15
3-4. Schematic Diagram –MAIN Section (1/2)– .................... 16
3-5. Schematic Diagram –MAIN Section (2/2)– .................... 17
3-2. Printed Wiring Boards –MAIN Section (1/2)– ................ 14
3-3. Printed Wiring Boards –MAIN Section (2/2)– ................ 15
3-4. Schematic Diagram –MAIN Section (1/2)– .................... 16
3-5. Schematic Diagram –MAIN Section (2/2)– .................... 17
4. EXPLODED VIEWS
4-1. Heat Sink (Main) Section ................................................ 19
4-2. MAIN Board Section ....................................................... 20
4-2. MAIN Board Section ....................................................... 20
5. ELECTRICAL PARTS LIST
...................................... 21
TABLE OF CONTENTS
Ver. 1.1
Click on the first or last page to see other XM-GTR6001 service manuals if exist.