Read Sony XAV-V630BT Service Manual online
XAV-V630BT
4
DESTINATION SETTING METHOD
When the chassis main assy (CHA1) is replaced, the destination
setting is necessary.
When the chassis main assy (CHA1) is replaced, the destination
setting is necessary.
Note 1: Remote commander is necessary.
(Refer
to
“ACCESSORIES” on page 24 about the remote com-
mander)
Note 2: It is not necessary for US, Canadian and MARUTI SUZUKI for
SWIFT models to perform the destination setting. Check whether
correct destination is set, refer to “Destination setting checking
method” on page 5. If correct destination is not set, perform the
destination setting according to the following procedure.
correct destination is set, refer to “Destination setting checking
method” on page 5. If correct destination is not set, perform the
destination setting according to the following procedure.
(When
correct
destination has been set for MARUTI SUZUKI for
SWIFT model, “MURUTI SUZUKI” screen is displayed on the
screen at startup. (Refer to Note in the “MODEL IDENTIFICA-
TION” on page 3))
screen at startup. (Refer to Note in the “MODEL IDENTIFICA-
TION” on page 3))
1. Preparing the Destination Setting
Be sure to solder the SL001 on the MAIN board before doing the
destination setting.
Be sure to solder the SL001 on the MAIN board before doing the
destination setting.
– MAIN Board (Conductor Side) –
SL001
SL001
2. Destination Setting
Set destination according to the procedure below.
Set destination according to the procedure below.
2-1. Setting the Destination Code
1. Turn the power on this unit.
2. Press the [OFF] button on the remote commander.
3. In the state of source off (Home screen is displayed), enter the
1. Turn the power on this unit.
2. Press the [OFF] button on the remote commander.
3. In the state of source off (Home screen is displayed), enter the
destination setting mode by pressing the buttons on the remote
commander in order of the [4] t [5] t [6] (press only the [6]
commander in order of the [4] t [5] t [6] (press only the [6]
button for two seconds).
4. The following screen is displayed and the destination setting
mode becomes effective.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
Note: Refer to following “2-2. Entering the Destination Code” for opera-
tion method.
<DESTINATION SETTING MODE>
0
0 0 0 0 0
E U R : 0 0 0 0 0 0
E 1 7 : 0 0 0 0 1 2
R U 2 : 0 0 0 0 0 4
E A : 0 0 0 0 1 A
U C : 0 0 0 0 0 1
E : 0 0 0 0 0 3
I N 2 : 0 0 0 0 1 9
E T 4 : 0 0 0 0 1 C
5. The resetting operation is executed by pressing the reset button
after the setting ends, and the unit returns to the normal condi-
tion.
tion.
2-2. Entering the Destination Code
Note 1: Input of the destination code cannot be performed by the keys of
main unit. Be sure to input the destination code by remote com-
mander.
mander.
Note 2: The model to which the remote commander is not attached can
also be operated by using the remote commander.
Note 3: The number buttons on the remote commander cannot be used.
1. Press the [V] or [v] button, and select the alphanumeric char-
acter of “0 to F”.
2. The digit advances by pressing the [b] button.
The digit returns by pressing the [B] button.
3. The setting is completed by pressing the [ENTER] button, and
the initialization operation is done.
2-3. Destination Code
Destination
Destination code
AEP and UK models (EUR)
000000
US and Canadian models (UC)
000001
E (NTSC) model (E)
000003
E (PAL) model (E17)
000012
Indian model (IN)
000015
MARUTI SUZUKI for SWIFT model (IN2)
000019
– Continued on next page –
Click on the first or last page to see other XAV-V630BT service manuals if exist.