Read Sony WX-GT90BT / WX-GT90BTE / WX-GT99BT / WX-GT99BTM Service Manual online
WX-GT90BT/GT90BTE/GT99BT/GT99BTM
43
• IC Pin Function Description
MAIN BOARD IC501 R5F3650ECDZ98FB (MAIN SYSTEM CONTROLLER)
(GT90BT: AEP, UK, E and Saudi Arabia/GT90BTE/GT99BT)
IC501 R5F3650KCDZ95FB (MAIN SYSTEM CONTROLLER) (GT90BT: US and Canadian models)
IC501 R5F3650ECDZ94FB (MAIN SYSTEM CONTROLLER) (GT99BTM)
Pin No.
Pin Name
I/O
Description
1
NOSE_SW
I
Front panel remove/attach detection signal input terminal Fixed at “L” in this unit
2
SIRCS
I
Remote control signal input from the remote control signal receiver
3
UNISO
-
Not used
4
UNISI
-
Not used
5
UNISCK
-
Not used
6
BYTE
I
External data bus width select signal input Connect to VSS in this unit
7
CNVSS
I
Flash write signal input terminal Normally operation: “L”, Flash write: “H”
8
XIN
I
Low speed operation clock signal input terminal (32.768 kHz)
9
XOUT
O
Low speed operation clock signal output terminal (32.768 kHz)
10
RESET
I
System reset signal input terminal Not used
11
OSCOUT
O
High speed operation clock signal output terminal (7.92 MHz)
12
VSS
-
Ground terminal
13
OSCIN
I
High speed operation clock signal input terminal (7.92 MHz)
14
VCC1
-
Power supply terminal (+3.3V)
15
NMI
I
Non-maskable interrupt signal input terminal Fixed at “H” in this unit
16
MEC_SELFSW
I
Detection signal input from the CD section (self switch)
17
BUIN
I
Back up power supply detection signal input terminal “L” is input at low voltage
18
NCO
-
Not used
19
RC_IN1
I
Rotary remote commander shift key input terminal
20
MC_RX
I
Serial data input from the sub system controller
21
NCO
-
Not used
22
MC_TX
O
Serial data output to the sub system controller
23
NCO
-
Not used
24
SYNC_OUT
O
Synchronize signal output to the DC/DC converter
(GT90BT: US, Canadian, AEP and UK/GT90BTE)
Synchronize signal output to the line amplifi er and DC/DC converter
(GT90BT: E and Saudi Arabia/GT99BT/GT99BTM)
(GT90BT: US, Canadian, AEP and UK/GT90BTE)
Synchronize signal output to the line amplifi er and DC/DC converter
(GT90BT: E and Saudi Arabia/GT99BT/GT99BTM)
25
SYNC_PRE5V_ON
-
Not used
26
BEEP
O
Beep sound drive signal output to the power amplifi er
27
I2C_SCK
O
IIC serial clock signal output terminal
28
I2C_SIO
I/O
IIC two-way serial data bus terminal
29
FW_TXD
O
Flash writer data output terminal
30
FW_RXD
I
Flash writer data input terminal
31
FW_CLK
I
Flash writer clock signal output terminal
32
FW_BUSY
O
Flash writer busy signal output terminal
33
XM_TX
O
Serial data output to the SIRIUSXM IN connector (GT90BT: US and Canadian models only)
34
XM_RX
I
Serial data input from the SIRIUSXM IN connector (GT90BT: US and Canadian models only)
35
XM_POWER_EN
O
Power supply on/off control signal output to the SIRIUSXM IN connector
(GT90BT: US and Canadian models only)
(GT90BT: US and Canadian models only)
36 to 38
NCO
-
Not used
39
EPM
O
EPM signal output terminal Fixed at “L” in this unit
40
NCO
-
Not used
41
MEC_LOAD
O
Motor (Loading) signal output to the CD section
42
MEC_EJECT
O
Motor (Eject) signal output to the CD section
43
NCO
-
Not used
44
CE
I
Chip enable signal input terminal Fixed at “H” in this unit
45
HIT2_DATA
I/O
IIC two-way serial data bus with the tuner unit
46
HIT2_SCL
O
IIC serial clock signal output to the tuner unit
47
HIT2_RESET
O
Reset signal output to the tuner unit “L”: reset
48 to 50
NCO
-
Not used
51
EN_SYS
O
Power supply on/off control signal output to the DC/DC converter
52
IPOD
-
Not used
53, 54
NCO
-
Not used
55
ACC_IN
I
Accessory power detection signal input terminal “L”: accessory power on
56
ATT
O
Muting on/off control signal output terminal “H”: muting on
Ver. 1.2
Click on the first or last page to see other WX-GT90BT / WX-GT90BTE / WX-GT99BT / WX-GT99BTM service manuals if exist.