Read Sony ZS-2000 (serv.man2) Service Manual online
– 6 –
Setting the clock
“– –:– –” indication appears in the
display until you set the clock.
display until you set the clock.
The Timer
Tip
The time display
system of this player is
the 12-hour system.
system of this player is
the 12-hour system.
1
Press and hold CLOCK until the hour digits flash.
2
Set the time.
1
Press TUNE • TIME
SET + or – to set the
hour and press
SET + or – to set the
hour and press
DISPLAY • ENTER
MEM.
2
Press TUNE • TIME
SET + or – to set the
minutes.
SET + or – to set the
minutes.
3
Press DISPLAY • ENTER
MEM.
MEM.
The clock starts from 00
seconds.
seconds.
To change the display to the daylight saving time
(summer time) indication
(summer time) indication
Press and hold SUMMER TIME for 2 seconds.
“Summer On ” appears in the display for a few
seconds.
seconds.
To cancel the summer time indication
Press and hold SUMMER TIME again.
“Summer Off” appears in the display for a few
seconds.
seconds.
TUNE
TIME SET –, +
TIME SET –, +
DISPLAY
ENTER MEM
ENTER MEM
CLOCK
SUMMER TIME
m
1
When the power is off, press TIME SIGNAL to
display “TIME SIGNAL ” indication.
display “TIME SIGNAL ” indication.
Do the following operations by checking the
display.
display.
2
Press TUNE • TIME SET + or – until the sound you
want appears in the display, and press DISPLAY •
ENTER MEM.
want appears in the display, and press DISPLAY •
ENTER MEM.
Display
Intervals
Wall Clock
Sounds on the hour the number of times
corresponding to
corresponding to
the
hour and
again
on
the
half hour once (Example: Three times at
3:00 p.m. and again at 3:30 p.m. once).
3:00 p.m. and again at 3:30 p.m. once).
Harp
Sounds on the hour once
Music Box
Sounds on the hour once
Chime
Sounds on the hour once
Organ
Sounds on the hour once
3
Press TUNE • TIME SET + or – to set the volume
you want, and press DISPLAY • ENTER MEM.
you want, and press DISPLAY • ENTER MEM.
Setting the time
signal
signal
When the power is off, you can hear the
time signal on this player. You can select
the sound for the time signal. Make sure
you have set the clock (see page 18).
time signal on this player. You can select
the sound for the time signal. Make sure
you have set the clock (see page 18).
TIME SIGNAL
Note
The time signal does
not sound when the
player is turned on.
not sound when the
player is turned on.
TUNE
TIME SET –, +
TIME SET –, +
DISPLAY
ENTER MEM
Display
continued
4
Press TUNE • TIME SET + or – to select the time for
the time signal function to work, and then press
DISPLAY • ENTER MEM.
the time signal function to work, and then press
DISPLAY • ENTER MEM.
Display
Time signal sounds
Off
Not at all
Every Hour
All day
Auto
7:00 a.m. - 10:00 p.m.
Once a Day*
Once a day
* If you selected “Wall Clock ” in step 2, you cannot select
“Once a Day ”
5
If you selected “Once a Day ” in step 4, set the time
for the time signal to sound. (If you selected other
items in step 4, omit this step.)
for the time signal to sound. (If you selected other
items in step 4, omit this step.)
1
Press TUNE • TIME SET + or – to set the hour
and press DISPLAY • ENTER MEM.
and press DISPLAY • ENTER MEM.
2
Press TUNE • TIME SET + or – to set the minutes
and press DISPLAY • ENTER MEM.
and press DISPLAY • ENTER MEM.
To check the sound types (demonstration mode)
Press and hold TIME SIGNAL for about 2 seconds.
You can hear the five types of sound once.
You can hear the five types of sound once.
Setting the time signal
(continued)
Saving power
Even when power is turned off, this
player consumes about 5.6 W for time
indication, timer operation, remote
control reception. If you use the saving
power function, you can reduce power
consumption to
player consumes about 5.6 W for time
indication, timer operation, remote
control reception. If you use the saving
power function, you can reduce power
consumption to
less
than 1
W.
DISPLAY
ENTER MEM
ENTER MEM
When the power is off, press and hold
DISPLAY • ENTER MEM for about 2 seconds.
DISPLAY • ENTER MEM for about 2 seconds.
The player enters the lower power consumption
standby mode.
standby mode.
To cancel the saving power
To make the time indication appear, press and hold
DISPLAY • ENTER MEM for about 2 seconds when the
DISPLAY • ENTER MEM for about 2 seconds when the
power is off.
Click on the first or last page to see other ZS-2000 (serv.man2) service manuals if exist.