Read Sony TA-SA200WR Service Manual online
TA-SA200WR
3
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
ADVANCE PREPARATION WHEN CONFIRMING OP-
ERATION
When the operation of the TA-SA200WR is confi rmed, it is nec-
essary to communicate the set of main unit with S-AIR and TA-
SA200WR and confi rm.
Confi rm the main unit with S-AIR, TA-SA200WR and EZW-RT10
etc. are prepared beforehand when you repair.
ERATION
When the operation of the TA-SA200WR is confi rmed, it is nec-
essary to communicate the set of main unit with S-AIR and TA-
SA200WR and confi rm.
Confi rm the main unit with S-AIR, TA-SA200WR and EZW-RT10
etc. are prepared beforehand when you repair.
DIRECTION OF EZW-RT10/RT10A INSTALLATION
When EZW-RT10/RT10A is install with the AMP board detached
of the set, the label of EZW-RT10/RT10A is the under and install.
When EZW-RT10/RT10A is install with the AMP board detached
of the set, the label of EZW-RT10/RT10A is the under and install.
label
EZW-RT10/RT10A
AMP board
Checking the
transmission status
transmission status
You can check the status of sound
transmission between the S-AIR main unit
and surround amplifier by checking the
S-AIR/STANDBY indicator on the
surround amplifier.
transmission between the S-AIR main unit
and surround amplifier by checking the
S-AIR/STANDBY indicator on the
surround amplifier.
S-AIR/
STANDBY
indicator
STANDBY
indicator
Status
Turns green.
The system is turned on,
wireless transmission is
activated and surround
signals are transmitting.
wireless transmission is
activated and surround
signals are transmitting.
Flashes green
quickly.
quickly.
The system is turned on
and wireless transmission
is activated, but surround
signals are not
transmitting.
and wireless transmission
is activated, but surround
signals are not
transmitting.
Flashes green
slowly.
slowly.
The system is turned on
and wireless transmission
is deactivated.
and wireless transmission
is deactivated.
Turns red.
The surround amplifier is
in standby mode while the
system is in standby mode
or wireless transmission is
deactivated.
in standby mode while the
system is in standby mode
or wireless transmission is
deactivated.
Turns off.
The surround amplifier is
turned off.
turned off.
Flashes orange.
The wireless transceiver is
not connected to the
surround amplifier.
not connected to the
surround amplifier.
Flashes red.
The surround amplifier’s
protection is active.
protection is active.
Sound
There is no sound.
Check the status of the S-AIR/STANDBY
indicator on the surround amplifier.
– Turns off.
Check the status of the S-AIR/STANDBY
indicator on the surround amplifier.
– Turns off.
s Check that the AC power cord (mains lead) of
the surround amplifier is connected securely.
s Turn the surround amplifier on by pressing
"/1 on the surround amplifier.
– Flashes orange.
s Check that the wireless transceiver is inserted
into the surround amplifier correctly.
– Flashes green quickly.
s Change the S-AIR ID settings of the S-AIR
main unit and surround amplifier.
cWhen you use this system with surround
speakers:
s Set the SURROUND SELECTOR switch of
the surround amplifier to SURROUND.
cWhen you use this system with surround
back speakers:
s Set [Surround Back] in [Speaker Settings] of
the S-AIR main unit to [Yes]. For details,
refer to the operating instructions of the
S-AIR main unit.
refer to the operating instructions of the
S-AIR main unit.
– Flashes red.
s Press
"/1 to turn off the surround amplifier,
and check the following items.
1 Are the + and – speaker cords short-
circuited?
2 Is anything blocking the ventilation
holes of the surround amplifier?
After checking the above items and fixing
any problems, turn on the surround amplifier.
If the cause of the problem cannot be found
any problems, turn on the surround amplifier.
If the cause of the problem cannot be found
Troubleshooting
even after checking all the above items,
consult your nearest Sony dealer.
consult your nearest Sony dealer.
– Flashes green slowly or turns red.
s Confirm the S-AIR IDs of the S-AIR main
unit and surround amplifier.
s Confirm the pairing setting.
s Sound transmission is poor. Move the
s Sound transmission is poor. Move the
surround amplifier so that the S-AIR/
STANDBY indicator turns green.
STANDBY indicator turns green.
s Move the system away from other wireless
devices.
s Avoid using any other wireless devices.
– Turns green.
s Check the speaker connections and settings.
s Depending on the source or the settings of the
s Depending on the source or the settings of the
S-AIR main unit, the effect of the speakers
may be less noticeable.
may be less noticeable.
MODEL IDENTIFICATION
Part No.
– Back Panel –
Model
Part No.
US and Canadian models
4-161-036-0
[]
AEP and UK models
4-161-036-1
[]
240V AC area in E and
Singapore models
Singapore models
4-161-036-2
[]
Chinese model
4-161-036-3
[]
Taiwan model
4-161-036-4
[]
Latin American models
4-161-036-5
[]
Russian model
4-161-036-7
[]
Australian model
4-161-036-8
[]
Iranian and Saudi Arabia
models
models
4-161-036-9
[]
Thai model
4-176-329-1
[]
Argentina model
4-176-329-2
[]
Ver. 1.2
Click on the first or last page to see other TA-SA200WR service manuals if exist.