Read Sony TA-S90D Service Manual online
TA-S90D
9
9
SECTION 5
DIAGRAMS
5-1.
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Boards:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
f
: internal component.
•
: Pattern from the side which enables seeing.
• Indication of transistor.
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
and tantalums.
• All resistors are in Ω and
1
/
4
W or less unless otherwise
specified.
•
f
: internal component.
• 2 : nonflammable resistor.
• 5 : fusible resistor.
• C : panel designation.
• 5 : fusible resistor.
• C : panel designation.
• A : B+ Line.
• B : B– Line.
• Voltages are dc with respect to ground under no-signal
• B : B– Line.
• Voltages are dc with respect to ground under no-signal
conditions.
no mark : Power on
(
no mark : Power on
(
) : Output is more than 1 W.
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Signal path.
F
: AUDIO
N
: MIC
• Abbreviation
AUS
: Australian model
EA
: Saudi Arabia model
SP
: Singapore model
E15
: 220 – 240 V AC Area in E model
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
Replace only with part number specified.
• Circuit Boards Location
AC OUTPUT board
SURROUND AMP board
SUB TRANS board
AC INPUT board
RELAY board
FRONT AMP board
PANEL board
B
These are omitted.
C
E
Q
5-2.
IC PIN FUNCTION DESCRIPTION
• FRONT AMP BOARD IC310 PT8300-S (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
VSS
—
Ground terminal
2
RESET_B
I
Reset signal input terminal Not used
3
CLK
I
Serial data transfer clock signal input from the tuner unit (ST-S90D)
4
LATCH
I
Serial data latch pulse input from the tuner unit (ST-S90D)
5
LED C
O
LED drive signal output of the CINEMA STUDIO C indicator (D706) “L”: LED on
6
LED B
O
LED drive signal output of the CINEMA STUDIO B indicator (D705) “L”: LED on
7
LED A
O
LED drive signal output of the CINEMA STUDIO A indicator (D704) “L”: LED on
8
LED EQ
O
LED drive signal output of the EQ indicator (D703) “L”: LED on
9
LED SUR
O
LED drive signal output of the SUR indicator (D702) “L”: LED on
10
LED BLU
O
LED drive signal output of the MULTI CHANNEL DECODING indicator (D781)
“L”: LED on
“L”: LED on
11
HP SW
I
Headphone detection signal input terminal “H”: headphone on
12
PROTECT
I
Over load detection signal input from speaker output “L”: over load
13
LATCHO
O
Serial data latch pulse output terminal Not used (open)
14
CLKO
O
Serial data transfer clock signal output terminal Not used (open)
15
—
—
Not used (open)
16
—
—
Not used (fixed at “L”)
17
—
—
Not used (open)
18
MUTING
O
Muting on/off control signal output terminal “L”: muting
19
LED PW
O
LED drive signal output of the I/1 indicator (D701) “L”: LED on
20
SUR RY
O
Relay drive signal output for the surround speaker (rear and center) protection “H”: on
21
F RY
O
Relay drive signal output for the front speaker protection “H”: on
22
STK PW
O
Power amplifier on/off selection signal output terminal “L”: standby, “H”: on
23
—
—
Not used (open)
24
STBY RY
O
Standby relay drive signal output terminal “L”: standby, “H”: power on
25
DATA OUT
O
Serial data output to the tuner unit (ST-S90D)
26
DATA IN
I
Serial data input from the tuner unit (ST-S90D)
27
PULLUP
—
Not used (open)
28
VCC
—
Power supply terminal (+5V)
Click on the first or last page to see other TA-S90D service manuals if exist.