Read Sony TA-FE230 / TA-FE330R / TA-FE530R Service Manual online
– 21 –
– 22 –
• IC Block Diagrams
– MAIN Board –
– MAIN Board –
IC101
LC7821
IC601
µPC1237HA
– CONTROL Board –
IC802
BA6208 (TA-FE330R/FE530R)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
CONTROL
LATCH
SHIFT RESISTER
LEVEL SHIFT
CL
DI
CE
VEE
L COM3
L7
L COM2
L5
L4
L2
VSS
S
RES
VDD
R COM3
R8
R7
R COM2
R6
R4
R2
R5
R COM1
R3
R1
L3
L1
L COM1
L6
L8
BUFFER
1
2
3
4
5
6
7
8
OVER LOAD DET
F/F
OFFSET DET
LATCH/
AUTORESET
V
CC
ON
MUTE
AC OFF
DET
V
CC
1
2
3
4
5
6
7
8
9
NC
OUTPUT 2
Vcc
GND
NC
INPUT 2
INPUT 1
NC
MOTOR
DRIVE
MOTOR
DRIVE
REG
SWITCH
SWITCH
OUTPUT1
3-8.
IC PIN FUNCTION DESCRIPTION
•
CONTROL BOARD IC801 TMP47C103N-JP47 (FUNCTION SWITCH CONTROL, LED DRIVER)
Pin No.
Pin Name
I/O
Description
1
XOUT
O
Main system clock output terminal (4 MHz)
2
XIN
I
Main system clock input terminal (4 MHz)
3
RESET
I
System reset signal input terminal “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
4
PMD
I
Setting terminal for the model
TA-FE230: fixed at “L”, TA-FE330R/FE530R: fixed at “H”
TA-FE230: fixed at “L”, TA-FE330R/FE530R: fixed at “H”
5
VOL+
O
Motor drive signal output to the volume motor drive (IC802) (volume up direction)
Used for the TA-FE330R/FE530R only (TA-FE230: Not used (pull up))
Used for the TA-FE330R/FE530R only (TA-FE230: Not used (pull up))
6
VOL–
O
Motor drive signal output to the volume motor drive (IC802) (volume down direction)
Used for the TA-FE330R/FE530R only (TA-FE230: Not used (pull up))
Used for the TA-FE330R/FE530R only (TA-FE230: Not used (pull up))
7
SW0
I
8
SW1
I
Rotary switch input of the INPUT SELECTOR (S801)
9
SW2
I
10
EON
I
Detection signal input of the enhanced other networks (EON)
Used for the TA-FE530R only (TA-FE230/FE330R: Not used (fixed at “H”))
Used for the TA-FE530R only (TA-FE230/FE330R: Not used (fixed at “H”))
11
PHONO
O
LED drive signal output of the PHONO LED (D808) “L”: LED on
12
TUNER
O
LED drive signal output of the TUNER LED (D809) “L”: LED on
13
CD
O
LED drive signal output of the CD LED (D810) “L”: LED on
14
GND
—
Ground terminal
15
AUX
O
LED drive signal output of the AUX LED (D811) “L”: LED on
16
DAT
O
LED drive signal output of the TAPE2/MD LED (D812) “L”: LED on
17
TAPE
O
LED drive signal output of the TAPE1/DAT LED (D813) “L”: LED on
18
MON
O
Tape monitor on/off control signal output terminal “L”: tape monitor on
Used for the TA-FE530R only (TA-FE230/FE330R: Not used (pull up))
Used for the TA-FE530R only (TA-FE230/FE330R: Not used (pull up))
19
PRY
O
AC on/off relay drive signal output terminal “L”: power on, “H”: standby mode
Used for the TA-FE330R/FE530R only (TA-FE230: Not used (pull up))
Used for the TA-FE330R/FE530R only (TA-FE230: Not used (pull up))
20
PKY
I
Power switch (S1; I/1) input terminal “H”: power on
Used for the TA-FE330R/FE530R only (TA-FE230: Not used (fixed at “H”))
Used for the TA-FE330R/FE530R only (TA-FE230: Not used (fixed at “H”))
21
MON
I
TAPE1 MONITOR switch (S802) input terminal When pressing the key: “H”
Used for the TA-FE530R only (TA-FE230/FE330R: Not used (fixed at “H”))
Used for the TA-FE530R only (TA-FE230/FE330R: Not used (fixed at “H”))
22
SIRCS
I
Sircs signal input from the remote control receiver (IC803)
Used for the TA-FE330R/FE530R only (TA-FE230: Not used (pull up))
Used for the TA-FE330R/FE530R only (TA-FE230: Not used (pull up))
23
MUTE
O
Audio line muting on/off control signal output terminal “H”: muting on
24
SCE
O
Chip enable signal output to the function switch (IC101)
25
SDT
O
Serial data output to the function switch (IC101)
26
SCK
O
Serial data transfer clock signal output to the function switch (IC101)
27
STOP
I
Detection signal input of the AC input
28
+3V
—
Power supply terminal (+3V)
Click on the first or last page to see other TA-FE230 / TA-FE330R / TA-FE530R service manuals if exist.