Read Sony TA-DA9000ES (serv.man2) Service Manual online
2
TA-DA9000ES
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED
LINE WITH MARK
0
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 ˚C higher than
• Unleaded solder melts at a temperature about 40 ˚C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 ˚C.
Caution: The printed pattern (copper foil) may peel away if the
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 ˚C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges oc-
cur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges oc-
cur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
i.LINK section
Pin
4 pins
Transmission speed
S200 (Maximum data
transmission speed 200
Mbps)
transmission speed 200
Mbps)
Transmission protocol A/M transmission protocol
Format (input)
Format (input)
Super Audio CD* (DSD
PLAIN)
2 channel linear PCM (IEC-
60958-3)
Sampling frequency: 44.1
kHz
PLAIN)
2 channel linear PCM (IEC-
60958-3)
Sampling frequency: 44.1
kHz
* Conforms to the copy protection technology of
DTLA (Revision 1.2).
General
Power requirements
Power consumption
600 W
Power consumption (during standby mode)
1 W
AC outlets
Dimensions
430
×
238
×
480 mm
including projecting parts and
controls
controls
Mass (Approx.)
28.5 kg
Supplied accessories
AC power coad (1)
Easy Setup Guide (1)
Easy Setup Guide (1)
Remote commander RM-LJ312 (1)
Operating Instructions for RM-LJ312 (1)
R6 (size-AA) batteries (3)
Design and specifications are subject to change
without notice.
without notice.
Area code
Power requirements
AEP
230 V AC, 50/60 Hz
Taiwan
110 V AC, 60 Hz
Korean
220 V AC, 60 Hz
Area code
AC outlets
AEP
1 switched, 100 W MAX
except AEP
−
(no AC outlet)
Area code
Power requirements
Click on the first or last page to see other TA-DA9000ES (serv.man2) service manuals if exist.