Read Sony STR-LSA1 Service Manual online
5
6
GB
Hooking Up the System
ANTENNA
AM
SPEAKERS
IMPEDANCE
USE 4-16
Ω
75
Ω
COAXIAL
FM
ANALOG IN
–
+
–
+
R
L
R
L
U
i.LINK S200
i.LINK
i.LINK
LINE OUT
L
R
v
v
i.LINK
LINE OUT
L
R
;
;
L
CD player,
etc.*
Audio Component Hookups
Required cables
i.LINK cables (not supplied)
Audio cables (not supplied)
White (L)
White (L)
Red (R)
Red (R)
*
You can connect components to either i.LINK S200 connector.
Connectors for connecting i.LINK
components
components
Connect a
To the
MD deck, CD player, etc.
i.LINK S200 connector
Note on i.LINK component hookups
If a metal object should fall into the i.LINK S200
connector, short-circuiting may occur and damage the
components.
connector, short-circuiting may occur and damage the
components.
About optional i.LINK connecting cables
Be sure to use the Sony i.LINK S200 connecting cables
(4 pins-4 pins).
(4 pins-4 pins).
Tape deck,
etc.
About i.LINK components to be used in
combination with the receiver
combination with the receiver
The following i.LINK components can be used with the
receiver.
• MDS-LSA1 MD Deck
• CDP-LSA1 CD Player
receiver.
• MDS-LSA1 MD Deck
• CDP-LSA1 CD Player
z
For general information about i.LINK
See “About i.LINK” on page 26.
Connectors for connecting other audio
components
components
Connect a
To the
Tape deck, etc.
ANALOG IN connectors
MD deck,
etc.*
23
GB
Other Operations
Recording
When recording to and from the i.LINK components, you
don’t have to do any operations on the receiver. For
details, refer to the operating instructions supplied with
the playback and recording components.
don’t have to do any operations on the receiver. For
details, refer to the operating instructions supplied with
the playback and recording components.
Do the procedure below to record from a component
connected to the ANALOG IN connectors or from the
built-in tuner to the i.LINK MD deck. Refer to the
instruction manual of the MD deck if you need help.
connected to the ANALOG IN connectors or from the
built-in tuner to the i.LINK MD deck. Refer to the
instruction manual of the MD deck if you need help.
1
Select the component to be recorded.
2
Prepare the component for playing.
3
Insert a blank MD into the MD deck and adjust the
recording level, if necessary.
recording level, if necessary.
4
Start recording on the MD deck, then start
playback on the playback component.
playback on the playback component.
Note
While the MD deck is recording from a component connected to
the ANALOG IN connectors or from the built-in tuner, you can’t
select other components.
the ANALOG IN connectors or from the built-in tuner, you can’t
select other components.
Adjusting the Brightness of
the Display Z
the Display Z
You can select one of three brightness levels for the
display. The JOG MENU button can be turned off when a
low brightness level is selected.
display. The JOG MENU button can be turned off when a
low brightness level is selected.
Press DIMMER on the remote while the power is on.
Each time you press DIMMER, the brightness of the
display changes as follows:
Each time you press DIMMER, the brightness of the
display changes as follows:
v
The display is fully lit and the JOG MENU button is on.
v
The display lights up dimly and the JOG MENU button is on.
v
The display lights up dimly and the JOG MENU button is off.
v
The display and the JOG MENU button are both off.
z
If any change occurs in the display information while the
display is turned off
The display turns back on (dimly) for several seconds to show
the new information, and then turns off again.
the new information, and then turns off again.
z
The brightness level of the displays on the MDS-LSA1 MD
Deck and CDP-LSA1 CD Player can be linked to that of the
receiver’s display through the i.LINK Control function
receiver’s display through the i.LINK Control function
The brightness level can be linked only when the i.LINK Control
function is activated. For details, see page 26.
function is activated. For details, see page 26.
Click on the first or last page to see other STR-LSA1 service manuals if exist.