STR-DG820 - Sony Audio Service Manual (repair manual). Page 2

Read Sony STR-DG820 Service Manual online

STR-DG820
2
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS  IDENTIFIED  BY  MARK 0 OR  DOTTED  LINE  
WITH  MARK 
0 ON  THE  SCHEMATIC  DIAGRAMS  AND  IN  
THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE  OPERATION.
REPLACE  THESE  COMPONENTS  WITH  SONY  PARTS 
 
WHOSE  PART  NUMBERS  APPEAR  AS  SHOWN  IN  THIS  
MANUAL  OR  IN  SUPPLEMENTS  PUBLISHED  BY  SONY.
Notes on chip component replacement
• 
Never reuse a disconnected chip component.
• 
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, 
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE  TEST
The AC leakage from any exposed metal part to earth ground and 
from all exposed metal parts to any exposed metal part having a 
return to chassis, must not exceed 0.5 mA (500 microamperes.). 
Leakage current can be measured by any one of three methods.
1.  A commercial leakage tester, such as the Simpson 229 or RCA 
WT-540A. Follow the manufacturers’ instructions to use these 
instruments.
2.  A battery-operated AC milliammeter. The Data Precision 245 
digital multimeter is suitable for this job.
3.  Measuring the voltage drop across a resistor by means of a 
VOM or battery-operated AC voltmeter. The “limit” indication 
is 0.75 V, so analog meters must have an accurate low-voltage 
scale. The Simpson 250 and Sanwa SH-63Trd are examples 
of a passive VOM that is suitable. Nearly all battery operated 
digital multimeters that have a 2 V AC range are suitable.  (See 
Fig. A)
Fig. A.  Using an AC voltmeter to check AC leakage.
1.5 k
Ω
0.15 
μF
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
About area codes
The area code of the receiver you purchased is 
shown on the lower right portion of the rear panel 
(see the illustration below).
Any differences in operation, according to the area 
code, are clearly indicated in the text, for example, 
“Models of area code AA only”.
SPEAKERS
SPEAKERS
CENTER
SURROUND BACK
FRONT A
FRONT B
L
R
SURROUND
L
R
L
L
R
R
Area code
AM tuner section
Tuning range
Antenna (aerial)
Loop antenna
Intermediate frequency
 
450 kHz
5)
You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off
the receiver. While holding down TUNING
MODE, press POWER on the receiver. All preset
stations will be erased when you change the tuning
scale. To reset the scale to 10 kHz (or 9 kHz),
repeat the procedure.
Video section
Inputs/Outputs
Video:
1 Vp-p, 75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p, 75 ohms
P
B
/C
B
: 0.7 Vp-p, 75 ohms
P
R
/C
R
: 0.7 Vp-p, 75 ohms
80 MHz HD Pass Through
Area code
Tuning scale
10 kHz step
9 kHz step
CEL, CEK, ECE
531 kHz –
1,602 kHz
U, CA 
             530 kHz – 
1,710 kHz
5)
531 kHz –
1,710 kHz
5)
General
Power requirements
Power output (DIGITAL MEDIA PORT)
DC OUT:
5V, 0.7 A MAX
Power consumption
Power consumption (during standby mode)
0.7 W
 
(When “CTRL:HDMI” in
HDMI menu is set to
“CTRL OFF”)
Dimensions (width/height/depth) (Approx.)
17 × 6 1/4 × 12 5/8 inches
 
(430 × 157.5 × 318 mm)
including projecting parts
and controls
Mass (Approx.)
18 lb 12 oz (8.5 kg) (U, CA)
8.4 kg (CEL, CEK, 
ECE, AU, TW, KR, E51)
Supplied accessories
Operating instructions
Quick Setup Guide (1)
FM wire antenna (aerial) (1)
AM loop antenna (aerial) (1)
Remote commander (RM-AAP021) (1)
R6 (size-AA) batteries (2)
Optimizer microphone (ECM-AC2) (1)
Design and specifications are subject to
change without notice.
Area code
Power consumption
U                           250 W
CA                        320 VA
Area code
Power requirements
U, CA                           120 V AC, 60 Hz
CEL, CEK, ECE
 230 V AC, 50/60 Hz
AU, E51
530 kHz –
1,710 kHz
5)
531 kHz –
1,710 kHz
5)
KR, TW
530 kHz –
1,610 kHz
5)
531 kHz –
1,602 kHz
5)
AU
240 V AC, 50 Hz
TW
110 V AC, 60 Hz
KR
220 - 230 V AC, 50/60 Hz
E51
120/220/240 V AC, 50/60 Hz
CEL, CEK, ECE,
 
AU, KR, E51
230 W
TW
220 W
ATTENTION  AU  COMPOSANT  AYANT  RAPPORT  
À  LA  SÉCURITÉ!
LES  COMPOSANTS  IDENTIFIÉS  PAR  UNE  MARQUE  0  SUR  
LES  DIAGRAMMES  SCHÉMATIQUES  ET  LA  LISTE  DES  
PIÈCES  SONT  CRITIQUES  POUR  LA  SÉCURITÉ  DE  FONC-
TIONNEMENT.  NE  REMPLACER  CES  COMPOSANTS  QUE  
PAR  DES  PIÈCES  SONY  DONT  LES  NUMÉROS  SONT  DON-
NÉS  DANS  CE  MANUEL  OU  DANS  LES  SUPPLÉMENTS  
PUBLIÉS  PAR  SONY.
Ver. 1.1
Page of 97
Display

Click on the first or last page to see other STR-DG820 service manuals if exist.