Read Sony STR-DA3600ES Service Manual online
STR-DA3600ES/DA4600ES
5
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
NOTE OF REPLACING THE IC3601 ON THE D-VIDEO
BOARD
Replacement of IC3601 on the D-VIDEO board used in this set
requires a special tool.
BOARD
Replacement of IC3601 on the D-VIDEO board used in this set
requires a special tool.
NOTE OF REPLACING THE IC5021 ON THE DSP
BOARD
IC5021 on the DSP board cannot exchange with single. When this
part on the DSP board is damaged, exchange the entire mounted
board.
BOARD
IC5021 on the DSP board cannot exchange with single. When this
part on the DSP board is damaged, exchange the entire mounted
board.
NOTE OF REPLACING THE IC3500 AND IC3501 ON
THE D-VIDEO BOARD (DA3600ES)
IC3500 and IC3501 on the D-VIDEO board cannot exchange with
single. When these parts on the D-VIDEO board are damaged, ex-
change the entire mounted board.
THE D-VIDEO BOARD (DA3600ES)
IC3500 and IC3501 on the D-VIDEO board cannot exchange with
single. When these parts on the D-VIDEO board are damaged, ex-
change the entire mounted board.
NOTE OF REPLACING THE IC3111, IC3511, IC3513
AND IC3514 ON THE D-VIDEO BOARD (DA4600ES)
IC3111, IC3511, IC3513 and IC3514 on the D-VIDEO board
cannot exchange with single. When these parts on the D-VIDEO
board are damaged, exchange the entire mounted board.
AND IC3514 ON THE D-VIDEO BOARD (DA4600ES)
IC3111, IC3511, IC3513 and IC3514 on the D-VIDEO board
cannot exchange with single. When these parts on the D-VIDEO
board are damaged, exchange the entire mounted board.
NOTE OF REPLACING THE IC8001 AND IC8013 ON
THE NETWORK BOARD
IC8001 and IC8013 on the NETWORK board cannot exchange
with single. When these parts on the NETWORK board are dam-
aged, exchange the entire mounted board.
THE NETWORK BOARD
IC8001 and IC8013 on the NETWORK board cannot exchange
with single. When these parts on the NETWORK board are dam-
aged, exchange the entire mounted board.
MODEL IDENTIFICATION
PART No.
Bar code
– Back Panel –
Model
Part No.
DA4600ES
4-174-079-0
[]
DA3600ES: US and Canadian models
4-174-079-1
[]
DA3600ES: AEP and UK models
4-174-079-2
[]
UPDATE OF SOFTWARE OF IC3610 ON THE D-VIDEO BOARD, IC6302 ON THE A-VIDEO BOARD (DA4600ES
ONLY), IC2501 ON THE MICOM BOARD, IC763 ON THE DISPLAY BOARD
Perform operation of the following when the update of software of the IC3610 on the D-VIDEO board, IC6302 on the A-VIDEO Board
(DA4600ES only), IC2501 on the MICOM board and IC763 on the DISPLAY board are necessary.
ONLY), IC2501 ON THE MICOM BOARD, IC763 ON THE DISPLAY BOARD
Perform operation of the following when the update of software of the IC3610 on the D-VIDEO board, IC6302 on the A-VIDEO Board
(DA4600ES only), IC2501 on the MICOM board and IC763 on the DISPLAY board are necessary.
Connect:
for PC
CIS Board
J861
J861
Procedure:
1. Connect J861 on the CIS board and PC by using the RS-232C cable.
2. Turn on the main power.
3. The update is executed by using PC.
4. When the update ends, turn off the main power.
5. Remove the RS-232C cable from the J861 on the CIS board and PC.
1. Connect J861 on the CIS board and PC by using the RS-232C cable.
2. Turn on the main power.
3. The update is executed by using PC.
4. When the update ends, turn off the main power.
5. Remove the RS-232C cable from the J861 on the CIS board and PC.
ERROR MESSAGES
If there is a malfunction, the display shows a code of two numbers and a message. You can check the status of the system by the message.
See the following table to solve the problem.
If there is a malfunction, the display shows a code of two numbers and a message. You can check the status of the system by the message.
See the following table to solve the problem.
messages
cause and response
PROTECTOR
The upper panel of the receiver is covered with something. The receiver will automatically turn off after a few
seconds. Remove the object covering the upper panel of the receiver and turn on the power again.
seconds. Remove the object covering the upper panel of the receiver and turn on the power again.
Click on the first or last page to see other STR-DA3600ES service manuals if exist.