Read Sony STR-DA1800ES Service Manual online
STR-DA1800ES
4
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
NOTE OF REPLACING THE CN3005, IC3008 AND
IC3700 ON THE D-VIDEO NW BOARD
CN3005, IC3008 and IC3700 on the D-VIDEO NW board cannot
exchange with single. When these parts are damaged, exchange the
complete mounted board.
IC3700 ON THE D-VIDEO NW BOARD
CN3005, IC3008 and IC3700 on the D-VIDEO NW board cannot
exchange with single. When these parts are damaged, exchange the
complete mounted board.
NOTE OF REPLACING THE CN2513 AND IC2811 ON
THE DIGITAL BOARD
CN2513 and IC2811 on the DIGITAL board cannot exchange with
single. When these parts are damaged, exchange the complete
mounted board.
THE DIGITAL BOARD
CN2513 and IC2811 on the DIGITAL board cannot exchange with
single. When these parts are damaged, exchange the complete
mounted board.
NOTE OF REPLACING THE IC5001 ON THE DSP BOARD
IC5001 on the DSP board cannot exchange with single. When this
part is damaged, exchange the complete mounted board.
IC5001 on the DSP board cannot exchange with single. When this
part is damaged, exchange the complete mounted board.
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitors (C930 and
C931 on the MAIN board) to discharge the capacitors (C930 and
C931 on the MAIN board).
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitors (C930 and
C931 on the MAIN board) to discharge the capacitors (C930 and
C931 on the MAIN board).
– MAIN Board (Conductor Side) –
C931 C930
800
:
/2 W
800
:
/2 W
Performing initial setup
operations (clearing all
memorized settings)
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure. This procedure can also
be used to revert back to the factory default
settings.
Be sure to use the buttons on the receiver to
perform this operation.
initialize the receiver by performing the
following procedure. This procedure can also
be used to revert back to the factory default
settings.
Be sure to use the buttons on the receiver to
perform this operation.
1
Press ?/1 to turn off the
receiver.
receiver.
2
Hold down ?/1 for 5 seconds.
The “CLEARING” appears on the
display panel for a while, then changes to
“CLEARED !”.
Changes or adjustments made to the
settings are now reset to the defaults.
display panel for a while, then changes to
“CLEARED !”.
Changes or adjustments made to the
settings are now reset to the defaults.
If there is a malfunction, a message appears on
the display panel. You can check the condition
of the system by the message. If any problem
persists, consult your nearest Sony dealer.
the display panel. You can check the condition
of the system by the message. If any problem
persists, consult your nearest Sony dealer.
PROTECTOR
Irregular current is output to the speakers, or
the receiver is covered and ventilation holes
are blocked. The receiver will automatically
turn off after a few seconds. Remove the
object covering the upper panel of the
receiver, check the speaker connection and
turn on the power again.
the receiver is covered and ventilation holes
are blocked. The receiver will automatically
turn off after a few seconds. Remove the
object covering the upper panel of the
receiver, check the speaker connection and
turn on the power again.
USB FAIL
An over current from the
(USB) port was
detected. The receiver will automatically
turn off after a few seconds. Check the
turn off after a few seconds. Check the
iPod/iPhone or USB device, then unplug it
and turn on the power again.
and turn on the power again.
Error messages
alligator clip
Note: Connect altogether the metal part
Note: Connect altogether the metal part
on the boards connected with the
chassis using the alligator clip.
– Example: When checking the DIGITAL board –
NOTE OF OPERATION CHECKS
When checking the operation of each board, be sure to connect the GND of each board to rear panel with alligator clips.
When checking the operation of each board, be sure to connect the GND of each board to rear panel with alligator clips.
Click on the first or last page to see other STR-DA1800ES service manuals if exist.