Read Sony SRS-X7 Service Manual online
SRS-X7
3
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
DO NOT REPLACE THE LITHIUM BATTERY
(US and Canadian models only)
The LITHIUM BATTERY for US and Canadian models cannot
be replaced. If it is necessary to replace the LITHIUM BATTERY,
replace the entire unit with a new one.
(US and Canadian models only)
The LITHIUM BATTERY for US and Canadian models cannot
be replaced. If it is necessary to replace the LITHIUM BATTERY,
replace the entire unit with a new one.
NOTE OF REPAIRING THE BOARDS
When boards other than the MAIN board installed by this unit are
defective, individual electrical parts that the mount is done cannot
be replaced.
Replace the mounted board, or replace the whole parts including
an applicable board.
When boards other than the MAIN board installed by this unit are
defective, individual electrical parts that the mount is done cannot
be replaced.
Replace the mounted board, or replace the whole parts including
an applicable board.
NOTE THE CN301, IC401 AND IC402 ON THE MAIN
BOARD REPLACING
CN301, IC401 and IC402 on the MAIN board cannot replace
with single. When these parts are damaged, replace the complete
mounted board.
BOARD REPLACING
CN301, IC401 and IC402 on the MAIN board cannot replace
with single. When these parts are damaged, replace the complete
mounted board.
NOTE OF WiFi MODULE REPLACING
When the WiFi module is replaced, the MAC address and DTCP-
IP ID have been changed.
Print the page 5 and 7, and pass it to the customer with the repaired
unit when you return the customer the repaired unit.
When the WiFi module is replaced, the MAC address and DTCP-
IP ID have been changed.
Print the page 5 and 7, and pass it to the customer with the repaired
unit when you return the customer the repaired unit.
PROCESSING OF REPLACING THE WiFi MODULE
When replacing the WiFi module (Ref. No. WIFI1), peel the de-
vice ID label stuck on the bottom side of the unit, and stick on the
new device ID label enclosed with the new WiFi module (Ref. No.
WIFI1).
When replacing the WiFi module (Ref. No. WIFI1), peel the de-
vice ID label stuck on the bottom side of the unit, and stick on the
new device ID label enclosed with the new WiFi module (Ref. No.
WIFI1).
1 Peel the device
ID
ID
label.
Model number
indication side
indication side
Caution indication side
– Bottom view –
2 Stick on the new
device ID label.
Device ID: XXXXXXXXXXXX
MAC Address: XX-XX-XX-XX-XX-XX
Note:
As for US and Canadian models, device ID label may be stuck on
the model number indication side.
the model number indication side.
Ver. 1.1
Click on the first or last page to see other SRS-X7 service manuals if exist.