Read Sony SRS-BT100 / SRS-BT100IK Service Manual online
SRS-BT100/BT100iK
2
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Notes on chip component replacement
•
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
Flexible Circuit Board Repairing
•
•
Keep the temperature of soldering iron around 270 °C during
repairing.
repairing.
•
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
circuit board (within 3 times).
•
Be careful not to apply force on the conductor when soldering
or unsoldering.
or unsoldering.
Note on the AC power adaptor
Use only the supplied AC power adaptor. Do not use any other AC power adaptor to avoid damaging the
speaker.
Use only the supplied AC power adaptor. Do not use any other AC power adaptor to avoid damaging the
speaker.
Polarity of the plug
SECTION 1
SERVICING NOTES
NOTE THE IC101 ON THE MAIN BOARD REPLAC-
ING
IC101 cannot exchange with single. When IC101 is damaged, ex-
change the entire mounted board.
ING
IC101 cannot exchange with single. When IC101 is damaged, ex-
change the entire mounted board.
Notes
• This transmitter is designed for iPod only. You cannot connect
• This transmitter is designed for iPod only. You cannot connect
any other portable audio players.
• Sony cannot accept responsibility in the event that data recorded
to iPod is lost or damaged when using an iPod connected to this
unit.
unit.
• This transmitter has been designed specifically to work with iPod
and has been certified to meet Apple performance standards.
Compatible iPod models
(SRS-BT100iK only)
(SRS-BT100iK only)
The compatible iPod models are as follows.
Update your iPod to use the latest software before you use
it.
Update your iPod to use the latest software before you use
it.
On copyrights
• iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
• The Bluetooth
®
word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by Sony Corporation is under license. Other
trademarks and trade names are those of their respective
owners.
such marks by Sony Corporation is under license. Other
trademarks and trade names are those of their respective
owners.
Ver. 1.1
Click on the first or last page to see other SRS-BT100 / SRS-BT100IK service manuals if exist.