Read Sony SRS-BT100 / SRS-BT100IK Service Manual online
SERVICE MANUAL
Sony Corporation
Published by Sony Techno Create Corporation
SRS-BT100/BT100iK
SPECIFICATIONS
WIRELESS SPEAKER SYSTEM
9-887-982-03
2010L05-1
©
2010.12
US Model
AEP Model
SRS-BT100
UK Model
SRS-BT100/BT100iK
Ver. 1.2 2010.12
Speaker section
Speaker system
90 mm, Full range, magnetically shielded
90 mm, Full range, magnetically shielded
Enclosure type
Bass reflex
Bass reflex
Impedance
4
4
Ω
Rated input power
15 W
15 W
Maximum input power
30 W
30 W
Amplifier section
Rated output
15 W + 15 W (10% T.H.D., 1 kHz, 4
15 W + 15 W (10% T.H.D., 1 kHz, 4
Ω)
Bass Boost
MEGA BASS
MEGA BASS
Audio input
Stereo minijack
Stereo minijack
× 1
Input impedance
4.7 k
4.7 k
Ω (at 1 kHz)
General
Power
DC 12V (supplied AC power adaptor)
DC 12V (supplied AC power adaptor)
Dimensions (w/h/d)
Approx. 400
Approx. 400
× 160 × 175 mm
(15
3
/
4
× 6
3
/
8
× 7 in.)
Mass
Approx. 2.5 kg (5 lb. 8 oz.)
Approx. 2.5 kg (5 lb. 8 oz.)
Communication System
Bluetooth Specification version 2.0 + EDR
Bluetooth Specification version 2.0 + EDR
Output
Bluetooth Specification Power Class 2
Bluetooth Specification Power Class 2
Maximum communication range
Line of sight approx. 10 m (30 ft)*
Line of sight approx. 10 m (30 ft)*
1
*
1
The actual range will vary depending on
factors such as obstacles between devices,
magnetic fields around a microwave oven,
static electricity, reception sensitivity,
antenna’s performance, operating system,
software application, etc.
factors such as obstacles between devices,
magnetic fields around a microwave oven,
static electricity, reception sensitivity,
antenna’s performance, operating system,
software application, etc.
*
2
Bluetooth standard profiles indicate the
purpose of Bluetooth communication
between devices.
purpose of Bluetooth communication
between devices.
*
3
Codec: Audio signal compression and
conversion format
*
4
Subband Codec
Supplied accessories
AC power cord (1)
AC power adaptor (1)
Operating Instructions (1)
AC power adaptor (1)
Operating Instructions (1)
Frequency band
2.4 GHz band (2.4000 GHz–2.4835 GHz)
2.4 GHz band (2.4000 GHz–2.4835 GHz)
Modulation method
FHSS
FHSS
Compatible Bluetooth profiles*
2
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio/Visual Remote Control Profile)
Volume UP/DOWN
AVRCP (Audio/Visual Remote Control Profile)
Volume UP/DOWN
Supported codecs*
3
SBC*
4
, MP3
Supported contents protection
SCMS-T
Design and specifications are subject to change
without notice.
without notice.
• SRS-BT100iK is a package model of SRS-BT100 and TMR-BT8iP.
Please refer to the service manual of TMR-BT8iP for information on TMR-BT8iP.
Please refer to the service manual of TMR-BT8iP for information on TMR-BT8iP.
SRS-BT100/BT100iK
2
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Notes on chip component replacement
•
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
Flexible Circuit Board Repairing
•
•
Keep the temperature of soldering iron around 270 °C during
repairing.
repairing.
•
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
circuit board (within 3 times).
•
Be careful not to apply force on the conductor when soldering
or unsoldering.
or unsoldering.
Note on the AC power adaptor
Use only the supplied AC power adaptor. Do not use any other AC power adaptor to avoid damaging the
speaker.
Use only the supplied AC power adaptor. Do not use any other AC power adaptor to avoid damaging the
speaker.
Polarity of the plug
SECTION 1
SERVICING NOTES
NOTE THE IC101 ON THE MAIN BOARD REPLAC-
ING
IC101 cannot exchange with single. When IC101 is damaged, ex-
change the entire mounted board.
ING
IC101 cannot exchange with single. When IC101 is damaged, ex-
change the entire mounted board.
Notes
• This transmitter is designed for iPod only. You cannot connect
• This transmitter is designed for iPod only. You cannot connect
any other portable audio players.
• Sony cannot accept responsibility in the event that data recorded
to iPod is lost or damaged when using an iPod connected to this
unit.
unit.
• This transmitter has been designed specifically to work with iPod
and has been certified to meet Apple performance standards.
Compatible iPod models
(SRS-BT100iK only)
(SRS-BT100iK only)
The compatible iPod models are as follows.
Update your iPod to use the latest software before you use
it.
Update your iPod to use the latest software before you use
it.
On copyrights
• iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
• The Bluetooth
®
word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by Sony Corporation is under license. Other
trademarks and trade names are those of their respective
owners.
such marks by Sony Corporation is under license. Other
trademarks and trade names are those of their respective
owners.
Ver. 1.1
SRS-BT100/BT100iK
3
SECTION 2
GENERAL
Thia section is extracted from
instruction manual.
instruction manual.
Location and Function of Parts
1 1 (power) button
Press to turn on the unit. Press and
hold to turn off the unit.
hold to turn off the unit.
2 ID SET (pairing) button
For pairing with other Bluetooth
device.
device.
3 VOLUME +/– buttons
Adjust the volume.
A beep sounds when the volume is set
to minimum or maximum.
A beep sounds when the volume is set
to minimum or maximum.
4 Power indicator (green)
5 Communication status
indicator (blue)
6 DC IN 12 V jack
Connects the supplied AC power
adaptor.
adaptor.
7 INPUT (audio input) jack
Connects to headphone jack of a
computer, portable audio device, etc.
computer, portable audio device, etc.
SRS-BT100/BT100iK
4
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
3-2. REAR CABINET SUB ASSY
Note:
This illustration sees the set from the back.
3-2. REAR CABINET SUB ASSY
(Page 4)
3-3. MAIN BOARD,
PANEL TOP BLOCK AND
FRONT PANEL SUB ASSY
(Page 5)
3-5. GRILLE CLOTH BLOCK
(Page 6)
3-4. POSITION OF SPEAKER LEAD WIRES
(Page 5)
SET
eight screws
(B3)
rear cabinet sub assy
When opening rear cabinet sub assy, please put the flat screw driver
in during gap of rear cabinet sub assy and front panel section and
open rear cabinet sub assy.
flat screw driver
gap
front panel section
rear cabinet sub assy
three claws
three claws
Note: This illustration sees the set from the bottom.