Read Sony SCD-XA5400ES Service Manual online
SCD-XA5400ES
15
4. Emergency History
You can check the Error history. You can also initialize the setup
data.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “3.
You can check the Error history. You can also initialize the setup
data.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “3.
Emergency History” by pressing the [3] button on the remote
commander. The following screen appears on the on-screen
display.
commander. The following screen appears on the on-screen
display.
Emg. History Check
Laser Hours CD 999h 59min
DVD 0h 0min
01. 01 05 04 04 00 92 46 00
00 00 00 00 00 00 23 45
02. 02 02 01 01 00 A9 4B 00
00 00 00 00 00 00 23 45
[Next]Next page [Prev]Prev page
[0]Return to Top Menu
2. You can check the total playback time of the Super Audio CD
and CD (
1
). The maximum time that can be displayed is 999h
59min.
Note: “DVD 0h 0min” on the screen does not change and always indicates
“0”.
3. You can check the 10 most recent error codes on the above
screen (
2
). To view the previous or next “Emergency History”
data screen, press the [
.
] or [
>
] button on the remote
commander.
ERROR CODES
There are three types of error codes: A, B, and C.
There are three types of error codes: A, B, and C.
A. Error code
Example of Error code
01. 01 05 04 04 00 92 46 00
00 00 00 00 00 00 23 45
The meaning of error code is as below:
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mechanical move error (5 changer)
26: Mechanical move stack error
30: DC motor adjustment error
31: DPD offset adjustment error
32: TE balance adjustment error
33: TE sensor adjustment error
34: TE loop gain adjustment error
35: FE loop gain adjustment error
36: Bad jitter after adjustment
40: Focus NG
42: Focus layer jump NG
51: Spindle stop error
52: Open kick spindle error
60: Focus on error
61: Seek fail error
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mechanical move error (5 changer)
26: Mechanical move stack error
30: DC motor adjustment error
31: DPD offset adjustment error
32: TE balance adjustment error
33: TE sensor adjustment error
34: TE loop gain adjustment error
35: FE loop gain adjustment error
36: Bad jitter after adjustment
40: Focus NG
42: Focus layer jump NG
51: Spindle stop error
52: Open kick spindle error
60: Focus on error
61: Seek fail error
Ver. 1.2
2. Select “3. Manual Adjustment” by pressing the [3] button on
the remote commander. The following screen appears on the
on-screen display.
on-screen display.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
[
V][v] Change Value
[RETURN]Return to previous menu
3. Select “6. Iop:” by pressing the [6] button on the remote com-
mander and wait until a hexadecimal number appears.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop: xx
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
[
V][v] Change Value
[RETURN]Return to previous menu
4. Use the conversion table etc. to convert the data displayed in
step 3 above from hexadecimal to decimal.
5. If the value is less than or equal to 93 (decimal), it is OK. How-
ever, if the value is greater than 93, the optical pickup block is
defective and needs to be replaced.
defective and needs to be replaced.
6. Press the [
O
RETURN] button on the remote commander to
return to the “Drive Manual Operation” menu.
7. Press the [0] button on the remote commander to return to the
top menu of Remocon Diagnosis Menu.
Release method:
Disconnect the power cord.
Disconnect the power cord.
Note: To release from this mode, do not use the power button on the set to
turn off the power but instead always unplug the power cord. Using
the power button to turn off the power could disable the set.
the power button to turn off the power could disable the set.
1
2
Click on the first or last page to see other SCD-XA5400ES service manuals if exist.