Read Sony SCD-XA5400ES Service Manual online
SCD-XA5400ES
14
SERVICE MODE
About The Remote Commander Used In TheService
Mode:
When the service mode is operated, the following, remote com-
mander is necessary.
(The service mode cannot be operated by remote commander to
which this machine is attached)
Remote commander (RM-ASP004): Part No. 1-479-272-21
About The Remote Commander Used In TheService
Mode:
When the service mode is operated, the following, remote com-
mander is necessary.
(The service mode cannot be operated by remote commander to
which this machine is attached)
Remote commander (RM-ASP004): Part No. 1-479-272-21
Note: Above-mentioned remote commander is one example. If it is the
one printed under a remote commander as “DVD”, any remote com-
mander can be operated.
mander can be operated.
1. Service Mode General Description
This mode let you make diagnosis and adjustment easily by using
the remote commander and the TV screen for HDMI input. The
instructions, diagnostic results, etc. are given on the TV screen.
Be sure to execute “3. IOP measurement” when the optical pickup
block is replaced.
This mode let you make diagnosis and adjustment easily by using
the remote commander and the TV screen for HDMI input. The
instructions, diagnostic results, etc. are given on the TV screen.
Be sure to execute “3. IOP measurement” when the optical pickup
block is replaced.
Preparations:
• TV monitor with HDMI input
• HDMI cable
• Remote commander for service mode (refer to “About The Re-
• TV monitor with HDMI input
• HDMI cable
• Remote commander for service mode (refer to “About The Re-
mote Commander Used In The Service Mode”)
Connection procedure:
Connect the TV monitor to the HDMI OUT jack (CN1701).
Connect the TV monitor to the HDMI OUT jack (CN1701).
HDMI OUT jack
(CN1701)
– Rear View –
HDMI cable
TV monitor
HDMI input
2. Entering Service Mode
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press two buttons of [
x
] and [
A
] on the set simultaneously for
3 seconds
3. A “SERVICE IN” message appears on the fl uorescent indica-
tor tube and the following Remocon Diagnosis Menu appears
on the TV monitor screen.
on the TV monitor screen.
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
Model Name :xxx-xxxxx
IF-con:Ver.xx.xx(xxxx)
Syscon:Ver.x.xxx
4. To execute each menu, press the corresponding number on the
remote commander.
Note: The following items are not used for service.
0. External Chip Check
1. Servo Parameter Check
5. Version Information
Release method:
Disconnect the power cord.
Disconnect the power cord.
Note: To release from this mode, do not use the power button on the set to
turn off the power but instead always unplug the power cord. Using
the power button to turn off the power could disable the set.
the power button to turn off the power could disable the set.
3. IOP measurement (Drive Manual Operation)
You can measure the IOP value.Procedure:
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “2
You can measure the IOP value.Procedure:
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “2
Drive Manual Operation” by pressing the [2] button on the
remote commander. The following screen appears on the on-
screen display
remote commander. The following screen appears on the on-
screen display
Drive Manual Operation
1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Mecha test mode
5. MIRR time Adjust
0. Return to Top Menu
Ver. 1.2
Click on the first or last page to see other SCD-XA5400ES service manuals if exist.