Read Sony NWZ-E583 / NWZ-E584 / NWZ-E585 Service Manual online
NWZ-E583/E584/E585
4
1-3. How to use the destination setting tool
Note 1: Please use the destination setting tool after closing music transfer
application software.
Will be described with below conditions as an example.
Destination : AEP, UK
Destination : AEP, UK
Procedure:
1. Connect “WALKMAN” to PC.
1. Connect “WALKMAN” to PC.
(The power supply of “WALKMAN” is automatically turned on)
2. Open the my computer window on PC, and confi rm how
“WALKMAN” is recognized on PC.
In the following example, “WALKMAN” is recognized by
MTP connection. In this case, the check of the drive letter is
unnecessary.
MTP connection. In this case, the check of the drive letter is
unnecessary.
In the following example, “WALKMAN” is recognized by
MSC connection. In this case, the check of the drive letter (at
this example, it is “F”) is necessary.
MSC connection. In this case, the check of the drive letter (at
this example, it is “F”) is necessary.
3. Start the command prompt application software, and move to
the folder in which the destination setting tool which wants to
write in is stored.
write in is stored.
(In this example, “cd c:\change_destination_E580_CEW2” is
inputted)
inputted)
C:\>cd c:\change_destination_E580_CEW2
C:\change_destination_E580_CEW2>
4. Input the following command according to the information
checked at step 2.
MSC connection : updating.bat f:
(The part of “f” changes with drive letters)
C:\change_destination_E580_CEW2>updating.bat f:
MTP connection : updating-mtp
C:\change_destination_E580_CEW2>updating-mtp
5. Confi rm that the following message has been displayed, and
input “y”, and press the Enter key on PC.
Note 2: When the Enter key on PC is pressed, the “WALKMAN” is formatted.
MTP F/W Update will start.
The WALKMAN unit reboots automatically after updating.
Before starting this program, close other application such
as WMP, Napster and Rhapsody etc.
Does this program run? (y/n)
The WALKMAN unit reboots automatically after updating.
Before starting this program, close other application such
as WMP, Napster and Rhapsody etc.
Does this program run? (y/n)
C:\change_destination_E580_CEW2>rem #
NOTE THE BOARD REPLACING
When the SW board or MAIN board are replaced, process it ac-
cording to the following order.
When the SW board or MAIN board are replaced, process it ac-
cording to the following order.
Note 1: The SW board cannot exchange with single. When exchanging
the SW board, exchange it at the same time as the MAIN board.
When SW and MAIN boards are replaced at the same time:
1.
Destination setting (page 4)
2.
Format (page 6)
3.
Reset all setting (page 6)
4.
Wallpapers setting (page 6)
When MAIN board is replaced alone:
1.
NC parameter setting (page 6)
Note 2: When SW and MAIN boards are replaced at the same time, NC
parameter setting need not be executed.
• When SW and MAIN boards are replaced at the same
time
1. Destination
setting
1-1. Outline
The destination cord is preset in factory. The destination should be
change when the SW and MAIN boards are replaced in repairing.
The destination cord is preset in factory. The destination should be
change when the SW and MAIN boards are replaced in repairing.
SW board
Model
Capacity
Part No. of
complete SW
+MAIN boards
Pre-installed
destination
code
NWZ-E583
4GB
9-885-189-56
EE
NWZ-E584
8GB
9-885-189-57
EE
NWZ-E585
16GB
9-885-189-58
CEW
Destination code
Area
Destination
code
Remark
(Default setting for each item)
Canadian
CA
EQ: None
AEP, UK
CEW2
EQ: None
East European
CEV
EQ: None
1-2. Preparation
Note 1: Please use the destination setting tool in Windows XP or later.
Note 2: Please install Windows Media Player 11 or later to make the unit
Note 2: Please install Windows Media Player 11 or later to make the unit
recognize as MTP.
Note 3: Confi rm the method of obtaining the destination setting tool to the
service headquarters.
Procedure:
1. Obtain the destination setting tool (“change_destination_
1. Obtain the destination setting tool (“change_destination_
E580_XX.zip” (XX: CA, CEW2 or EE)).
2. Copy the destination setting tool to root directory of C drive on
PC.
Note 4: The destination setting tool can be saved any drive as long as the
folder path is with English (one byte character).
Described with the example that “the folders were saved under
root directory of C drive” on this service manual.
Click on the first or last page to see other NWZ-E583 / NWZ-E584 / NWZ-E585 service manuals if exist.