Read Sony NW-ZX2 Service Manual online
NW-ZX2
4
SECTION 1
SERVICING NOTES
ABOUT REUSE OF LITHIUM ION STORAGE BATTERY
PACK
It cannot reuse, when the lithium ion storage battery pack is re-
moved from adhesive sheet (in the PANEL (REAR TOP) assy). Be
sure to replace the new parts.
PACK
It cannot reuse, when the lithium ion storage battery pack is re-
moved from adhesive sheet (in the PANEL (REAR TOP) assy). Be
sure to replace the new parts.
ABOUT INSULATING OF LITHIUM ION STORAGE
BATTERY PACK
When the lithium ion storage battery pack is removed from board,
insulate the end of wire by a tape etc. to prevent short-circuited of
the wire part of lithium ion storage battery pack.
When the lithium ion storage battery pack is removed from board,
insulate the end of wire by a tape etc. to prevent short-circuited of
the wire part of lithium ion storage battery pack.
lithium ion storage
battery pack
battery pack
wire
Wrap by the tape etc. and
insulate the end of wire.
insulate the end of wire.
ABOUT THE REPLACING OF THE BATTERY ASSY
(BAT1)
When the BATTERY ASSY (BAT1) is replaced, refer to SERVICE
MODE “4-3. BATTERY” on page 39.
(BAT1)
When the BATTERY ASSY (BAT1) is replaced, refer to SERVICE
MODE “4-3. BATTERY” on page 39.
NOTE OF DISPOSAL OF THE LITHIUM ION STORAGE
BATTERY PACK
Please dispose of the lithium ion storage battery pack in the fol-
lowing procedure if you want to dispose of the lithium ion storage
battery pack that is installed in the unit.
BATTERY PACK
Please dispose of the lithium ion storage battery pack in the fol-
lowing procedure if you want to dispose of the lithium ion storage
battery pack that is installed in the unit.
Note 1:
The SPACER (BATT) has been changed in the midway of pro-
duction. There are two types of case if the battery recycle label
has been affi xed to the SPACER (BATT), and affi xed directly to
the lithium ion storage battery pack.
has been affi xed to the SPACER (BATT), and affi xed directly to
the lithium ion storage battery pack.
Procedure:
1. Confi rm the shape of the SPACER (BATT).
• There is a battery recycle label, and there is no hole. (Fig. A)
1. Confi rm the shape of the SPACER (BATT).
• There is a battery recycle label, and there is no hole. (Fig. A)
→ go to step 2
• There is no battery recycle label, and there is a hole. (Fig. B)
→ go to step 3
Fig. B: There is no battery
recycle label, and
there is a hole.
Fig. A: There is a battery
recycle label, and
there is no hole.
2. Peeling off the battery recycle label from the SPACER (BATT).
Note 2:
Do not use a battery recycle label that was peeled off.
SPACER (BATT)
The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit.
3. Confi rm that the battery recycle label has been affi xed on the
lithium ion storage battery pack.
• Battery recycle label is not affi xed. (Fig. C)
→ go to step 4
• Battery recycle label is affi xed. (Fig. D)
→ go to step 5
Fig. C: There is no battery
recycle
recycle
label.
Fig. D: There is a battery
recycle
recycle
label.
4. Affi x a new battery recycle label to the lithium ion storage bat-
tery pack (Fig. C).
Part No.
Description
4-415-645-03
BATTERY RECYCLE LABEL (L)
Paste position
Note 3:
Paste position of the label does not need to be strictly controlled.
In reference to the fi gure below, please paste it into not out of the
outer shape of the lithium ion storage battery pack.
outer shape of the lithium ion storage battery pack.
16 mm
18.55 mm
lithium ion
storage battery
pack
storage battery
pack
battery recycle
label
label
5. Dispose the lithium ion storage battery pack.
Note 4:
The lithium ion storage battery pack for the repair has been af-
fi xed battery recycle label.
DESTINATION ABBREVIATIONS
The following abbreviations for model destinations are used in this
service manual.
The following abbreviations for model destinations are used in this
service manual.
• Abbreviations
AR :
AR :
Argentina
model
AUS :
Australian
model
CH
: Chinese model
CND : Canadian model
EE
EE
: East European model
IDN
: Indonesian model
JE
:
Tourist
model
MX
: Mexican model
NOTE OF REPLACING THE MAIN BOARD
When the MAIN board is replaced, you must perform the destina-
tion setting. Refer to “DESTINATION SETTING” on page 5, and
perform the destination setting.
Moreover, when the MAIN board is replaced, the MAC address
and DTCP-IP ID have been changed.
Print the page 13 and 15, and pass it to the customer with the re-
paired unit when you return the customer the repaired unit.
When the MAIN board is replaced, you must perform the destina-
tion setting. Refer to “DESTINATION SETTING” on page 5, and
perform the destination setting.
Moreover, when the MAIN board is replaced, the MAC address
and DTCP-IP ID have been changed.
Print the page 13 and 15, and pass it to the customer with the re-
paired unit when you return the customer the repaired unit.
Click on the first or last page to see other NW-ZX2 service manuals if exist.