Read Sony MDS-S38 / MDS-S39 / MDS-S707 Service Manual online
— 3 —
To Exposed Metal
Parts on Set
Parts on Set
0.15µF
1.5k
Ω
AC
voltmeter
(0.75V)
voltmeter
(0.75V)
Earth Ground
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
ing safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE
The AC leakage from any exposed metal part to earth Ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers). Leak-
age current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers). Leak-
age current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a pas-
sive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a pas-
sive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
MODEL IDENTIFICATION
— BACK PANEL —
— BACK PANEL —
Parts No.
4-989-525-1
4-989-525-2
4-989-525-3
4-989-525-4
4-989-525-5
4-989-525-6
4-989-525-7
Parts No.
Model
US model
Canadian model
AEP model
UK model
Singapore model
Hong Kong model
Tourist model
Product country
MALAYSIA
MALAYSIA
MALAYSIA
MALAYSIA
MALAYSIA
MALAYSIA
JAPAN
TABLE OF CONTENTS
1. SERVICING NOTE
.......................................................... 5
2. GENERAL
.......................................................................... 8
3. DISASSEMBLY
3-1. Front Panel ......................................................................... 22
3-2. Back Panel and Main Board ............................................... 23
3-3. Bracket (T), (L) and (R) ...................................................... 24
3-4. BD Board ........................................................................... 24
3-5. SUB Chassis ........................................................................ 25
3-6. Shutter Assembly ................................................................ 25
3-7. Over Write Head ................................................................. 26
3-8. Slider Complete Assembly .................................................. 27
3-2. Back Panel and Main Board ............................................... 23
3-3. Bracket (T), (L) and (R) ...................................................... 24
3-4. BD Board ........................................................................... 24
3-5. SUB Chassis ........................................................................ 25
3-6. Shutter Assembly ................................................................ 25
3-7. Over Write Head ................................................................. 26
3-8. Slider Complete Assembly .................................................. 27
4. TEST MODE
..................................................................... 28
5. ELECTRICAL ADJUSTMENTS
............................... 31
6. DIAGRAMS
6-1. Circuit Boards Location ...................................................... 36
6-2. Block Diagrams
6-2. Block Diagrams
• BD Section ....................................................................... 37
• Main Section .................................................................... 39
• Main Section .................................................................... 39
6-3. Printed Wiring Board — BD Section — ............................. 42
6-4. Schematic Diagram — BD Section — ............................... 45
6-5. Schematic Diagram — Main Section — ............................ 49
6-6. Printed Wiring Board — Main Section — .......................... 53
6-7. Schematic Diagram — Panel Section — ............................ 55
6-8. Printed Wiring Board — Panel Section — ......................... 57
6-9. IC Block Diagrams ............................................................. 60
6-10. IC Pin Functions ............................................................... 65
6-4. Schematic Diagram — BD Section — ............................... 45
6-5. Schematic Diagram — Main Section — ............................ 49
6-6. Printed Wiring Board — Main Section — .......................... 53
6-7. Schematic Diagram — Panel Section — ............................ 55
6-8. Printed Wiring Board — Panel Section — ......................... 57
6-9. IC Block Diagrams ............................................................. 60
6-10. IC Pin Functions ............................................................... 65
7. EXPLODED VIEWS
7-1. Main Section ....................................................................... 74
7-2. Front Panel Section ............................................................. 75
7-3. Mechanism Deck Section (1) (MDM-3B) .......................... 76
7-4. Mechanism Deck Section (2) (MDM-3B) .......................... 77
7-2. Front Panel Section ............................................................. 75
7-3. Mechanism Deck Section (1) (MDM-3B) .......................... 76
7-4. Mechanism Deck Section (2) (MDM-3B) .......................... 77
8. ELECTRICAL PARTS LIST
........................................ 78
Click on the first or last page to see other MDS-S38 / MDS-S39 / MDS-S707 service manuals if exist.