Read Sony ICF-CD7000 Service Manual online
3
ICF-CD7000
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•
Unleaded solder melts at a temperature about 40
°
C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
MODEL INDENTIFICATION
– Bottom View –
PART No.
Model
PART No.
US (White, Beige) model
3-093-131-0[]
US (Black) model, Hotel model
3-093-131-1[]
Canadian (White) model
3-093-132-0[]
Canadian (Black) model
3-093-132-1[]
Italian, Russian (White) models
3-093-133-0[]
Italian, Russian (Black) models
3-093-133-1[]
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
During normal operation of the equipment, emission of the laser
diode is prohibited unless the upper lid is closed while turning ON
the S419. (push switch type)
The following checking method for the laser diode is operable.
diode is prohibited unless the upper lid is closed while turning ON
the S419. (push switch type)
The following checking method for the laser diode is operable.
•
Method
Emission of the laser diode is visually checked.
Emission of the laser diode is visually checked.
1. Open the CD lid assy.
2. Push the S419 as shown in Fig.1.
2. Push the S419 as shown in Fig.1.
Note:
Do not push the detection lever strongly, or it may be bent or
damaged.
damaged.
3. Press the
CD
u
button.
4. Check the object lens for confirming normal emission of the
laser diode. If not emitting, there is a trouble in the automatic
power control circuit or the optical pick-up.
In this operation, the object lens will move up and down few
times along with inward motion for the focus search.
power control circuit or the optical pick-up.
In this operation, the object lens will move up and down few
times along with inward motion for the focus search.
Fig.1 Method to push the S419
S419
Note 1:
Beige color is Liv type.
Note 2:
Hotel model (US) is black color.
COLOR VARIATION
Destination
COLOR
WHITE
BLACK
BEIGE
US
z
z
z
Canadian
z
z
Italian
z
z
Russian
z
z
Ver. 1.2
HOW TO DISTINGUISH MODEL FOR ORIGINAL AND
FOR HOTEL
FOR HOTEL
In black color of US model, there is a model for hotel besides an
original model.
Two parts of BUTTON (SNOOZE) and PANEL (CD LID) are
different in an original model and the model for hotel.
Please distinguish an original model and the model for hotel
respectively referring to the figure below.
original model.
Two parts of BUTTON (SNOOZE) and PANEL (CD LID) are
different in an original model and the model for hotel.
Please distinguish an original model and the model for hotel
respectively referring to the figure below.
surface:
silver color
reverse:
like green color (for original)
silver or resin color (for hotel)
surface:
silver color
reverse:
like green color (for original)
silver or resin color (for hotel)
– BUTTON (SNOOZE) –
– PANEL (CD LID) –
Click on the first or last page to see other ICF-CD7000 service manuals if exist.