ICF-CD513 - Sony Audio Service Manual (repair manual). Page 4

– 4 –

This section is extracted from
instruction manual.

• Built-in CD player with Shuffle/Repeat

function.

• PLL (Phase Locked Loop) Synthesized Tuner

with 15 memory presets for easy one button
tuning.

• Powerful bass with MEGABASS sound system.
• Single alarm function - which can be used as

timer.

• Summer time (daylight saving time)

calculation.

The AM channel step differs depending on areas.
The channel step of this unit is factory-set to
10 kHz (US, Canadian models)/
9 kHz (AEP model).

North and South

10 kHz

American countries

Other countries

 9 kHz

A

The unit can be installed without the spacer.

Mark the position of the 4 holes by
using the supplied template. Use a drill
to make the holes (size 6.5 mm dia.,

9

/

32

 inch). (See Fig. A- )

When the cabinet door overhangs the
shelf and obstructs the unit, you can
adjust the unit/shelf height.
First set the L mark to the dot which
becomes the lowest position, then you
can adjust the height in 4 steps (H••L)
by turning the spacer counterclockwise.
(See Fig. A- )

Install the unit with the supplied
mounting screws. (See Fig. A- )

• Since the unit is very heavy, be careful when

installing the unit.

• To reduce the risk of fire, do not place any

heating or cooking appliance beneath this
unit.

• Install the unit so that its AC power cord can

be connected directly to a wall outlet. Do not
use a converter or extension cord.

• Be sure that the AC power cord has no slack

when using the unit, since the cord acts as an
FM wire antenna. If the AC power cord has
some slack, wind it up to the cord hook until
the cord has no slack.

• The unit has a built-in ferrite bar antenna for

AM radio reception. Check the condition of
AM reception before fixing in position.

• Install the unit as far as possible from a source

of noise. (for example, refrigerator, microwave
oven, fluorescent lamp, etc.)

A

<

<

<

a

b

c

Repeat steps 

 and 

 to set the minute.

After setting the minute, press 

 to start

the counting of the seconds, and you will
hear two short beeps.

• To set the current time rapidly, hold down

 

 or 

.

• The clock system varies depending on the

model you own.
12-hour system: “AM 12:00” = midnight
24-hour system: “0:00” = midnight

• In step 

, when you press 

after the

minute setting to activate the clock, the seconds
start counting from zero.

Press 

.

“

” is displayed and the time indication

changes to summer time.
To deactivate the summer time function, press

 again.

The AM channel step differs depending on areas.
The channel step of this unit is factory-set to
9 kHz or 10 kHz to match the frequency
allocation system of the country as listed.
You can change the channel step.

North and South
American countries

10 kHz

0.1 MHz

Other countries

9 kHz

0.05 MHz

Press 

 to turn off the power.

While holding down 

, keep

pressing 

 

  for more than 5

seconds. Two short beeps will sound,
and the AM channel step will be
changed.
If you proceed step 

 again, the channel

step changes again.

• When the AM channel step is changed, the

preset stations will be erased.

• When the AM channel step is changed, the FM

channel step is also changed.

Plug in the clock radio.

The display will flash “AM 12:00” or “0:00”.

Press 

 for a few seconds.

You will hear a beep and the hour will start
to flash in the display.

Press  

 or 

until the correct hour appears in the
display.

An 8 cm (3-inch) CD can be played without an
adaptor.

Press Z 

 and place a CD

on the disc tray.

Press Z 

to close the disc

tray.

Press 

 u.

The player plays all the tracks once.

Press 

  once.

The minute will flash.