Read Sony ICF-CD513 Service Manual online
– 11 –
no mark : US, Canadian models
< > : AEP model
< > : AEP model
AM IF ADJUSTMENT
Adjust for a maximum reading on level meter
T1
450 kHz
AM FREQUENCY COVERAGE ADJUSTMENT
Adjustment Part
Frequency Display
Reading on Digital Voltmeter
L4
530 kHz
2.65
±
0.05 V
<531 kHz>
Confirmation
1,710 kHz
8.8
±
1.0 V
<1,602 kHz>
<8.3
±
1.0 V>
AM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter
L3
580 kHz <621 kHz>
CT2
1,490 kHz <1,404 kHz>
FM FREQUENCY COVERAGE ADJUSTMENT
Adjustment Part
Frequency Display
Reading on Digital Voltmeter
L2
87.5 MHz
2.6
±
0.05 V
Confirmation
108 MHz
8.8
±
1.0 V
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter
L1
87.5 MHz
CT1
108 MHz
Adjustment Location: MAIN board (See page 13)
FM VCO Adjustment
Setting:
Procedure:
1. Connect the frequency counter to TP(ST VCO), TP(TU - +B)
1. Connect the frequency counter to TP(ST VCO), TP(TU - +B)
on the MAIN board, as shown the figure below.
2. Tune the set to 98 MHz.
3. Adjust RV1 on the MAIN board for 76 kHz reading on the
3. Adjust RV1 on the MAIN board for 76 kHz reading on the
frequency counter.
Specified Value: 75.95 to 76.05 kHz
Adjustment Location: MAIN board (See page 13)
SECTION 5
ELECTRICAL ADJUSTMENTS
TUNER SECTION
0 dB=1 µV
[AM]
Setting:
Function
Function
: RADIO
Band switch : AM
[FM]
Setting:
Function
Function
: RADIO
Band switch : FM
• Attention
BP1 Desoldering
(Must be short after measurement)
(Must be short after measurement)
• Repeat the procedures in each adjustment several times, and the
frequency coverage and tracking adjustments should be finally
done by the trimmer capacitors.
done by the trimmer capacitors.
AM RF signal
generator
30% amplitude
modulation by
400 Hz signal
Output level: as low as possible
modulation by
400 Hz signal
Output level: as low as possible
Put the lead-wire
antenna close to
the set.
antenna close to
the set.
+
–
–
level meter
set
4
Ω
MAIN board
speaker terminal (CN301)
speaker terminal (CN301)
FM RF signal
generator
22.5 kHz frequency
deviation by 400 Hz
signal
Output level: as low as possible
deviation by 400 Hz
signal
Output level: as low as possible
+
–
–
level meter
set
4
Ω
0.01
µ
F
MAIN board
TP (FM IN)
TP (FM IN)
MAIN board
speaker terminal (CN301)
speaker terminal (CN301)
TP (FEG GND)
digital voltmeter
100 k
Ω
MAIN board
TP (VT)
FM RF SSG
Carrier frequency: 98 MHz
Modulation: 400 Hz, 30% FM modulation
Output level: 0.1 V (100 dB)
Modulation: 400 Hz, 30% FM modulation
Output level: 0.1 V (100 dB)
MAIN board
TP (FM IN)
TP (FM IN)
0.01
µ
F
set
TP (FEG GND)
1
µ
F
TP (ST VCO)
+
–
–
frequency counter
33 k
Ω
TP (TU - +B)
+
MAIN board
Click on the first or last page to see other ICF-CD513 service manuals if exist.