Read Sony ICD-UX71 / ICD-UX71F / ICD-UX81 / ICD-UX81F / ICD-UX91F Service Manual online
ICD-UX71/UX71F/UX81/UX81F/UX91F
2
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
FLEXIBLE CIRCUIT BOARD REPAIRING
• Keep the temperature of soldering iron around 270 °C during
• Keep the temperature of soldering iron around 270 °C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Dimensions (w/h/d) (not incl.
projecting parts and controls) (JEITA)*
projecting parts and controls) (JEITA)*
5
34.4
× 99.0 × 13.4 mm
Mass (JEITA)*
5
Approx. 48 g including NH-AAA rechargeable
battery
battery
*
5
Measured value by the standard of JEITA
(Japan Electronics and Information
Technology
Technology
Industries
Association)
Supplied accessories
Design and specifi cations are subject to
change without notice.
change without notice.
IC Recorder (1)
Remove the film on the display window
before you use the IC recorder.
before you use the IC recorder.
NH-AAA (size AAA) rechargeable
battery (1)
battery (1)
(AEP, E, Chinese, Korea model)
Stereo headphones (1)
USB connection support cable (1)
Carrying case (1)
Battery case (1)
(AEP, E, Chinese, Korea model)
CD-ROM (1)
(The operating instructions are stored as
PDF files.) (AEP, E model)
PDF files.) (AEP, E model)
Operating Instructions
Ver. 1.1
Click on the first or last page to see other ICD-UX71 / ICD-UX71F / ICD-UX81 / ICD-UX81F / ICD-UX91F service manuals if exist.