Read Sony ICD-S7 Service Manual online
9
ICD-S7
4. Sleep test
• Pressing the x
• Pressing the x
•B key causes the set to enter the sleep state.
• When the HOLD switch is ON, the LCD is turned off. When
OFF, the LCD is turned on.
• Press any keys to exit the sleep state.
5. Beep test
• Beep sound of 1.3 kHz or 2 kHz is output.
• Beep sound of 1.3 kHz or 2 kHz is output.
6. SIO test
• Perform the connection test of the RTC, EEPROM and serial to
• Perform the connection test of the RTC, EEPROM and serial to
parallel conversion IC.
• As to the test result, if all of the connection test are OK,
“****OK****” is displayed. If the connection test of the RTC is
NG, “**RTCNG**” is displayed. If the EEPROM is NG,
“**EEPNG**” is displayed.
NG, “**RTCNG**” is displayed. If the EEPROM is NG,
“**EEPNG**” is displayed.
7. Key entry test
• When the any key is pressed, the entry key and the A/D converted
• When the any key is pressed, the entry key and the A/D converted
value (hexadecimal) of the two channel keys are displayed.
• When the STOP key is pressed, the A/D value of the key is
displayed while the key is depressed. When the key is released,
the screen returns to the test menu.
the screen returns to the test menu.
8. Battery remaining power test
• The detected A/D value (hexadecimal) of the battery remaining
• The detected A/D value (hexadecimal) of the battery remaining
power is displayed.
9. LED/EL test
• LED (red and green) and EL are all turned on.
• LED (red and green) and EL are all turned on.
any keys
any keys
SLEEP TEST
SLEEP IN
LCD OFF
(with HOLD OFF status)
x•B
(with HOLD ON status)
x•B
x•B
BEEP TEST
1.3K BEEP
2.0K BEEP
1.3K BEEP
1.3K BEEP
2.0K BEEP
:
:
(set)
x•B
(select),
.
>
STOP
STOP
STOP
x•B
SIO TEST
SIO OK
STOP
x•B
KEY TEST
0-FF 1-FF
STOP
x•B
BATT TEST
STOP
10. USB test
• When the menu starts the USB self-check, either presence or
• When the menu starts the USB self-check, either presence or
absence of the Vbus is judged.
(Vbus is present: “VBUS: ON”, Vbus is absent: “VBUS: OFF”)
(Vbus is present: “VBUS: ON”, Vbus is absent: “VBUS: OFF”)
• The USB driver always works regardless of presence or absence
of the USB signal only when Vbus is available during the USB
test. At this time, turning on HOLD causes the set to move to the
suspend state. Turning off the Vbus causes the set to return to the
test menu.
test. At this time, turning on HOLD causes the set to move to the
suspend state. Turning off the Vbus causes the set to return to the
test menu.
11. DC-IN test
LCD : Detection result of external DC power supply is display is
LCD : Detection result of external DC power supply is display is
displayed of LCD.
12. DATA READ test (not used)
Not use for test command design check or verification.
Not use for test command design check or verification.
13. Rest menu
• Pressing the x
• Pressing the x
•B key causes the set to enter the menu
initialization standby state.
• When the following keys are all entered and the x
•B key is
pressed, the initialization is executed. At the same time, the
WakeUp signal is checked, too.
WakeUp signal is checked, too.
Check keys: VOLUME+ , VOLUME– , A-B REPEAT ,
INDEX , STOP , zREC , ERASE , . ,
x•B , > , MENU , FOLDER
and check states of Memory Stick insert and
outsert ( EJECT ).
x•B , > , MENU , FOLDER
and check states of Memory Stick insert and
outsert ( EJECT ).
• If all tests end in success, “**ALLOK**” is displayed. If the key
entry is NG or if any of the keys is not pressed yet, “**KEYNG**”
appears. If saving in the EEPROM is NG, “**MENUNG**”
appears.
appears. If saving in the EEPROM is NG, “**MENUNG**”
appears.
x•B
LED TEST
LED EL ON
STOP
x•B
RESET
RESET KEY
RESET OK
x•B
In the case that the key entry
and saving in the EEPROM end correctly,
after the check key is entered.
and saving in the EEPROM end correctly,
after the check key is entered.
STOP
STOP
x•B
Suspend
USB
VBUS ON
LCD OFF
When Vbus is on, HOLD key turns on.
STOP
or cut Vbus
or cut Vbus
STOP
cut Vbus
cut Vbus
x•B
DC JACK
JACK ON OFF
( )
STOP
Click on the first or last page to see other ICD-S7 service manuals if exist.