Read Sony ICD-PX333 / ICD-PX333D / ICD-PX333F / ICD-PX333M Service Manual online
ICD-PX333/PX333D/PX333F/PX333M
3
SECTION 1
SERVICING NOTES
ABOUT THE BOARDS REPLACING
When the boards installed in this unit are defective, exchange the
complete mounted board.
However the microphone jack (J301), headphone jack (J302),
When the boards installed in this unit are defective, exchange the
complete mounted board.
However the microphone jack (J301), headphone jack (J302),
[HOLD•POWER ON/OFF] switch (S941) and [NOISE CUT]
switch (S401) on the MAIN board are exchangeable. Refer to “4.
EXPLODED VIEWS” (page 19).
switch (S401) on the MAIN board are exchangeable. Refer to “4.
EXPLODED VIEWS” (page 19).
ABOUT THE DESTINATION SETTING WHEN REPLAC-
ING THE MAIN BOARD
When the MAIN board of this unit is replaced, perform processing
according to the following procedure.
ING THE MAIN BOARD
When the MAIN board of this unit is replaced, perform processing
according to the following procedure.
Precaution
The contents which are not opened to customers are included
in the following procedure. After you are cautious of handling of
information, execute work under the suffi cient administration.
The contents which are not opened to customers are included
in the following procedure. After you are cautious of handling of
information, execute work under the suffi cient administration.
1. About the preparing of tools
Download the tools used by this work from the homepage of TISS.
When the tools cannot be confi rmed by TISS, confi rm to the ser-
vice headquarters.
Download the tools used by this work from the homepage of TISS.
When the tools cannot be confi rmed by TISS, confi rm to the ser-
vice headquarters.
2. Setting
method
Note: The destination setting is impossible when battery voltage is not
enough.
Do work using the battery with suffi cient battery level.
Procedure:
1. Equip this unit with battery.
2. Connect this unit to the PC.
1. Equip this unit with battery.
2. Connect this unit to the PC.
PC
To USB port
of PC
of PC
To (USB)
connector
connector
IC recorder
USB connecting
cable
cable
3. On PC, unzip the model setting fi le to get folder on PC.
4. On PC, open the unzipped folder, and select the folder corre-
4. On PC, open the unzipped folder, and select the folder corre-
sponding to the model name and destination of this unit.
5. On PC, copy the “DEVINFO.UPG” fi le included in the folder
selected at step 4 to root folder of this unit.
1.
SERVICING NOTES
.............................................
3
2. DISASSEMBLY
2-1. Disassembly
Flow
........................................................... 5
2-2. Case
(Front)
Assy
............................................................ 6
2-3. LCD
Assy
(LCD1)
.......................................................... 7
2-4. MAIN Board Block ........................................................ 8
2-5. Speaker
2-5. Speaker
(SP1)
................................................................. 9
2-6. LCD
Holder
.................................................................... 9
2-7. Electret Cap Microphone (MIC1), MAIN Board ........... 10
3.
TEST MODE
............................................................ 11
4.
EXPLODED VIEWS
4-1. Case Front Section .......................................................... 18
4-2. MAIN Board Section ...................................................... 19
4-3. Case (Rear) Section ........................................................ 20
4-2. MAIN Board Section ...................................................... 19
4-3. Case (Rear) Section ........................................................ 20
5. ACCESSORIES
....................................................... 21
TABLE OF CONTENTS
Ver. 1.1
Click on the first or last page to see other ICD-PX333 / ICD-PX333D / ICD-PX333F / ICD-PX333M service manuals if exist.