Read Sony HCD-ZX10 / MHC-ZX10 Service Manual online
5
This section is e
xtracted from
instr
uction man
ual.
6
Step 2: Setting the time
You must set the time before using the timer
functions.
functions.
The clock is on a 24-hour system for the European
model, and on a 12-hour system for other models.
model, and on a 12-hour system for other models.
For illustration purposes, the 24-hour system
model is used.
model is used.
1
Press MODE SELECT when the system
is turned off.
is turned off.
“Clock Set ?” appears.
When the system is in the Power Saving
Mode, “Clock Set ?” will not appear. Either
set Power Saving Mode off, or follow the
steps on the following page (“To change the
time”) after turning the power on.
When the system is in the Power Saving
Mode, “Clock Set ?” will not appear. Either
set Power Saving Mode off, or follow the
steps on the following page (“To change the
time”) after turning the power on.
2
Press PUSH ENTER.
The hour indication flashes.
?/1
(Power)
(Power)
1
To attach the front speaker pads
Attach the supplied front speaker pads to the
bottom of the speakers to stabilize the speakers
and prevent them from slipping.
bottom of the speakers to stabilize the speakers
and prevent them from slipping.
Inserting two size AA (R6)
batteries into the remote
batteries into the remote
E
Tip
With normal use, the batteries should last for about
six months. When the remote no longer operates the
system, replace both batteries with new ones.
six months. When the remote no longer operates the
system, replace both batteries with new ones.
Note
If you do not use the remote for a long period of time,
remove the batteries to avoid possible damage from
battery leakage.
remove the batteries to avoid possible damage from
battery leakage.
When carrying this system
Do the following to protect the CD mechanism.
Make sure that all discs are removed from the
unit.
Make sure that all discs are removed from the
unit.
1 Press FUNCTION repeatedly until “CD”
appears in the display.
2 Hold down V-GROOVE and press ?/1 so that
“LOCK” appears in the display.
Step 1: Hooking up the system
(continued)
(continued)
2,3,4,5,6
E
e
e
7
Getting Started
3
Move the multi stick toward v or V
repeatedly to set the hour.
repeatedly to set the hour.
4
Move the multi stick toward B.
The minute indication flashes.
5
Move the multi stick toward v or V
repeatedly to set the minute.
repeatedly to set the minute.
6
Press PUSH ENTER.
To cancel the menu operation
Press MODE SELECT.
Tips
• Refer to the illustration to use the multi stick. Place
your finger on the center of the multi stick and
move in the direction you want (up/down or left/
right shown v/V or b/B in this manual).
move in the direction you want (up/down or left/
right shown v/V or b/B in this manual).
PUSH
ENTER
• If you’ve made a mistake, start over from step 1.
To change the time
The previous explanation shows you how to set
the time while the power is off. To change the
time while the power is on, do the following:
the time while the power is off. To change the
time while the power is on, do the following:
1 Press MODE SELECT repeatedly to select “Set
Up Mode”, then press PUSH ENTER.
2 Move the multi stick toward b or B repeatedly
to select “Timer Set Up ?”, then press PUSH
ENTER.
ENTER.
3 Move the multi stick toward b or B repeatedly
to select “Clock Set ?”, then press PUSH
ENTER.
ENTER.
4 Perform steps 3 through 6 on the left.
Note
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
the power cord or if a power failure occurs.
Up (v)
Right (B)
Left (b)
Down (V)
Click on the first or last page to see other HCD-ZX10 / MHC-ZX10 service manuals if exist.