Read Sony HCD-RV900D Service Manual online
3
HCD-RV900D
0-2-3. ROM Check Sum
The revision number of ROM (IC203) that the program for
the DVD system processor (IC206) is stored.
the DVD system processor (IC206) is stored.
0-2-4. Model Type
Model name is displayed. (MHC-xxxx)
0-2-5. Region
Model destination code is displayed. (2 digits number)
0-3. EEPROM Check
0-3-1. Sampling Check
EEPROM check at every 64 words.
It compares read data with write data of each address. When
there are discrepancies between two data, it displays error.
It compares read data with write data of each address. When
there are discrepancies between two data, it displays error.
0-3-2. Detail Check
EEPROM check at every 1 word.
It compares read data with write data of each address. When
there are discrepancies between two data, it displays error.
It compares read data with write data of each address. When
there are discrepancies between two data, it displays error.
0-4. GP I/O Check
Pull up/down setting check of the DVD system processor (IC206)
pin 150, 151 and 154 (for clock setting port).
pin 150, 151 and 154 (for clock setting port).
0-5. SD Bus Check
SD bus data check between DVD decoder (IC701) and D-RAM
(IC706).
(IC706).
0-6. Video Check
Output the color bars for video level adjustment.
0-7. Audio Check
Output the test signal (1kHz sine wave) for 5.1 CH test.
1.
DRIVE AUTO ADJUSTMENT
On the Test Mode Menu screen, press the
[1]
key on the remote
commander, and the Adjustment Menu will be displayed.
## Drive Auto Adjustment ##
Adjustment Menu
0. ALL
1. DVD-SL
2. CD
3. DVD-DL
Exit: RETURN
Normally,
[10/0]
is selected to adjust DVD (single layer), CD and
DVD (dual layer) in this order. But, individual items can be adjusted
for the case where adjustment is suspended due to an error. In this
mode, the adjustment can be made easily through the operation
following the message displayed on the screen.
The disc used for adjustment must be the one specified for
adjustment.
for the case where adjustment is suspended due to an error. In this
mode, the adjustment can be made easily through the operation
following the message displayed on the screen.
The disc used for adjustment must be the one specified for
adjustment.
Note:
After parts related to the servo circuit (RF amplifier, DSP, motor
driver, EEPROM so on) are replaced, re-adjusting the servo circuit is
necessary. Select “ALL” at “1. DRIVEAUTO ADJUSTMENT” and
adjust DVD-SL (single layer), CD and DVD-DL (dual layer).
driver, EEPROM so on) are replaced, re-adjusting the servo circuit is
necessary. Select “ALL” at “1. DRIVEAUTO ADJUSTMENT” and
adjust DVD-SL (single layer), CD and DVD-DL (dual layer).
1-0. ALL
Press the
[10/0]
key on the remote commander, and the servo set
data in EEPROM will be initialized. Then, 1. DVD-SL disc, 2. CD
disc and 3. DVD-DL disc are adjusted in this order.
Each time one disc was adjusted, it is ejected. Replace it with the
specified disc following the message. You can finish the adjustment
by pressing the
disc and 3. DVD-DL disc are adjusted in this order.
Each time one disc was adjusted, it is ejected. Replace it with the
specified disc following the message. You can finish the adjustment
by pressing the
[RETURN]
button on the remote commander.
Note:
During adjustment of each disc, the measurement for disc type judg-
ment is made. As automatic adjustment does not judge the disc
type unlike conventional models, take care not to insert wrong type
discs. Also, do not give a shock during adjustment.
ment is made. As automatic adjustment does not judge the disc
type unlike conventional models, take care not to insert wrong type
discs. Also, do not give a shock during adjustment.
1-1. DVD-SL (single layer)
Press the
[1]
key on the remote commander and insert a DVD single
layer disc following the message. Then the adjustment will be made
through the steps below, then adjusted values will be written to the
EEPROM.
through the steps below, then adjusted values will be written to the
EEPROM.
DVD Single Layer Disc Adjustment Steps:
1.
Sled tilt reset
2.
Disc check memory SL
3.
Wait 300 msec
4.
Set disc type SL
5.
LD on
6.
Spindle start
7.
Wait 1 sec
8.
Focus servo on 0
9.
Auto track offset adjust
10. CLVA on
11. Wait 500 msec
12. Tracking on
13. Wait 1 sec
14. Sled on
15. Check CLV on
16. Auto LFO adjust
17. Auto focus offset adjust
18. Auto tilt position adjust
19. Auto focus gain adjust
20. Auto focus offset adjust
21. EQ boost adjust
22. Auto loop filter offset adjust
23. Auto track gain adjust
Search Check
11. Wait 500 msec
12. Tracking on
13. Wait 1 sec
14. Sled on
15. Check CLV on
16. Auto LFO adjust
17. Auto focus offset adjust
18. Auto tilt position adjust
19. Auto focus gain adjust
20. Auto focus offset adjust
21. EQ boost adjust
22. Auto loop filter offset adjust
23. Auto track gain adjust
Search Check
24. 32 track jump forward
25. 32 track jump reverse
26. 500 track jump forward
27. 500 track jump reverse
25. 32 track jump reverse
26. 500 track jump forward
27. 500 track jump reverse
28. All servo stop
29. EEP copy loop filter offset
29. EEP copy loop filter offset
1-2. CD
Press the
[2]
key on the remote commander and insert a CD disc
following the message. Then the adjustment will be made through
the steps below, then adjusted values will be written to the EEPROM.
the steps below, then adjusted values will be written to the EEPROM.
CD Adjustment Steps
1.
Sled tilt rest
2.
Disc check memory CD
3.
Wait 500 msec
4.
Set disc type CD
5.
LD on
6.
Spindle start
7.
Wait 500 msec
8.
Focus servo on 0
9.
Auto track offset adjust
10. CLVA on
11. Wait 500 msec
11. Wait 500 msec
Click on the first or last page to see other HCD-RV900D service manuals if exist.