Read Sony HCD-E800W Service Manual online
HCD-E800W
2
NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
FLEXIBLE CIRCUIT BOARD REPAIRING
• Keep the temperature of soldering iron around 270 °C during
• Keep the temperature of soldering iron around 270 °C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Self-diagnosis Function
When the self-diagnosis function is activated to prevent the system
from malfunctioning, an error code appears in the front panel display,
or just
from malfunctioning, an error code appears in the front panel display,
or just
appears without any messages on the entire screen. In
these cases, check the following.
When an error code appears in the front panel
display
display
When just
appears without any messages on
the entire screen
Contact your nearest Sony dealer or local authorized Sony service
facility.
facility.
Error code
Corrective action
Exxxx
Contact your nearest Sony dealer or local authorized Sony
service facility and give the error code.
service facility and give the error code.
SYSTEM ERR
UPDATE NG
Turn off the system and disconnect the AC power cord
(mains lead) from the wall outlet (mains), then reconnect and
turn the system on. If the system does not work normally,
consult your nearest Sony dealer or local authorized Sony
service facility.
(mains lead) from the wall outlet (mains), then reconnect and
turn the system on. If the system does not work normally,
consult your nearest Sony dealer or local authorized Sony
service facility.
This appliance is
classified as a CLASS 1
LASER product. This
marking is located on the
rear exterior.
classified as a CLASS 1
LASER product. This
marking is located on the
rear exterior.
Design and specifications are subject to change
without notice.
without notice.
General
Power requirements
50/60 Hz
Power consumption
On: 120 W
Standby: 0.3 W (at the
Power Saving mode)
Standby: 0.3 W (at the
Power Saving mode)
Output voltage/current
(DIGITAL MEDIA PORT)
(DIGITAL MEDIA PORT)
DC 5 V/700 mA
LAN (100)
100BASE-TX Terminal
EXT
External memory slot (For
connecting the external
memory)
DC output: 5 V 500 mA
Max
connecting the external
memory)
DC output: 5 V 500 mA
Max
Taiwan model:
120 V AC, 50/60 Hz
Other models:
220 V - 240 V AC,
120 V AC, 50/60 Hz
Other models:
220 V - 240 V AC,
Dimensions (approx.)
430 mm × 93 mm × 400
mm (w/h/d) incl.
projecting parts
430 mm × 93 mm × 430
mm (w/h/d) (incl. Wireless
transceiver)
mm (w/h/d) incl.
projecting parts
430 mm × 93 mm × 430
mm (w/h/d) (incl. Wireless
transceiver)
Mass (approx.)
5.4 kg
Click on the first or last page to see other HCD-E800W service manuals if exist.