Read Sony HBD-NF7220 Service Manual online
HBD-NF7220
6
TEST DISC
Part No.
Description
Layer
J-6090-199-A
BLX-104
Single Layer
J-6090-200-A
BLX-204
Dual Layer
J-2501-307-A
CD (HLX-A1)
J-2501-305-A
HLX-513
Single Layer (NTSC)
J-2501-306-A
HLX-514
Dual Layer (NTSC)
J-6090-077-A
HLX-506
Single Layer (PAL)
J-6090-078-A
HLX-507
Dual Layer (PAL)
Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883-
989-1[]) (page 1-3 to 1-14E) for the use of BLX-104/204.
Operation and Display:
1. BLX-104
Procedure:
1. Select
Procedure:
1. Select
23.976Hz/1080P.
2. Play “4. Motion picture”.
3. Check whether player can play back or not.
4. Check each outputs.
3. Check whether player can play back or not.
4. Check each outputs.
• HDMI
• Audio
• Speaker out
• Audio
• Speaker out
* When 1080/24P monitor is nothing, 1080i (59.94Hz or 50Hz)
can use instead of 1080/24P.
However this is temporary correspondence.
* It is necessary to lower the output of HDMI to 480P or 576P or
less.
2. BLX-204
Procedure:
1. Select 1080i (59.94Hz or 50Hz).
2. Play “4. Motion picture”.
3. Check whether player can play back or not.
Procedure:
1. Select 1080i (59.94Hz or 50Hz).
2. Play “4. Motion picture”.
3. Check whether player can play back or not.
(Check the picture and sound output)
3. CD (HLX-A1)
Procedure:
Check whether player can play back or not.
(Check the sound output)
Procedure:
Check whether player can play back or not.
(Check the sound output)
4. HLX-513/514 (NTSC), HLX-506/507 (PAL)
Procedure:
1. After displayed Main Menu, select “1. Video Signal”.
2. Play “1. Color bar 100%”.
Procedure:
1. After displayed Main Menu, select “1. Video Signal”.
2. Play “1. Color bar 100%”.
(Check the picture and sound output)
3. Return to Main Menu.
4. Play “5. Demonstration 4:3” or “6. Demonstration 16:9”.
4. Play “5. Demonstration 4:3” or “6. Demonstration 16:9”.
(Check the picture and sound output)
NOTE OF REPLACING THE WLAN/BT COMBO CARD
AND THE COMPLETE MB1305 BOARD
When the WLAN/BT combo card or complete MB1305 board are
replaced, execute the below BD service mode.
AND THE COMPLETE MB1305 BOARD
When the WLAN/BT combo card or complete MB1305 board are
replaced, execute the below BD service mode.
Note: The operation in this mode must use a remote commander and TV
monitor.
Procedure:
1. Connect this unit with TV monitor.
2. Press the [
1. Connect this unit with TV monitor.
2. Press the [
?/1
] button to turn the power on.
3. Press button in order of the [x] [DISPLAY] [X] [M]
on the remote commander.
(Make the interval when each button is pressed within two sec-
onds)
onds)
4. Enter the BD service mode. The OSD menu on TV monitor
can be operated by remote commander.
5. Press the [m] button on the remote commander to select
“Diag”, and press the [ ] button on the remote commander.
6. Press the [,] button on the remote commander to select
“Bluetooth Device Test”. (Screen 1)
7. Press the [ ] button on the remote commander to select “(1)
Bluetooth Enable”.
8. Press
the
[ ] button on the remote commander, wait until the
display show “Status: Bluetooth Enable Successful!” (Screen
2).
2).
9. Press the [m] button on the remote commander to select “(3)
Write Bluetooth device address to Registry”.
10. Press the [ ] button on the remote commander, wait until the
display show “Status: Write Successful!” (Screen 3).
11. Press the [RETURN] button on the remote commander to se-
lect “Wireless LAN Test”. (Screen 4)
12. Press the [ ] button on the remote commander to select “(5)
Write P2P address to Registry”.
13. Press the [ ] button on the remote commander, wait until the
display show “Status: Write Successful!” (Screen 5).
14. Press the [m] button on the remote commander to select “(6)
P2P Registry Check”.
15. Press the [ ] button on the remote commander to check the
P2P devise address is the same as shown in Screen 5.
(Displayed characters/values in the following fi gure are
example)
16. Press the [
?/1
] button to turn the power off.
Diag
Diag
Category: Bluetooth Device Test
Category: Bluetooth Device Test
(2) Bluetooth Disable
(3) Write Bluetooth device address to Registry
(4) Bluetooth Inquiry Test
(3) Write Bluetooth device address to Registry
(4) Bluetooth Inquiry Test
Status: Bluetooth Enable Successful!
HELP: [UP] [DOWN] [ENT] [RET]
(Screen 1)
(Screen 2)
Category:
Bluetooth Device Test
(1) Bluetooth Enable
Click on the first or last page to see other HBD-NF7220 service manuals if exist.